View Single Post
Old 05-15-2014, 13:58   #47 (permalink)
umerfarooq
Freak Poster
 
Join Date: Jul 2007
Posts: 175
Member: 540932
Status: Offline
Thanks Meter: 36
EasyJtag Suite ver.: 1.3.4.3 / wxWidgets 3.1.0-W-U started.
Operating system ver.: Windows 7 (build 7601, Service Pack 1).
Successefuly connected to box on COM7Box S/N: 18FF900BE3CD5E21, ,FW Ver.: 01.50Box Working Mode: JTAG Box.Box Drivers version: 3.0.0.0, are OK
Z3X Card Serial : AAFA-E5F5 , ver: 22
Z3X EasyJtag Software ver. 1.3.4.3
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 18FF900BE3CD5E21, ,FW Ver.: 01.50
CMD Pullup Level:1103 mV
CMD Active Level:1433 mV
eMMC Device Information
EMMC CID : 15010056545530304DF156273F257FAC
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 07/2012 Rev.0xf1
EMMC NAME: VTU00M , S/N: 1445412645
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VTU00M_1445412645_20140404_1336.extcsd
Done.
Running:SAMSUNG: Smart Factory Reset + Format...
Z3X EasyJtag Software ver. 1.3.4.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1103 mV
CMD Active Level:1433 mV
Sending Smart Wipe Request...
Wiping Card... Please do not touch it!!!
Done.
Please don't forget to repair extCSD from backup!!!
Running:SAMSUNG: MoviNAND Format...
Z3X EasyJtag Software ver. 1.3.4.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1103 mV
CMD Active Level:1433 mV
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Sending Internal Reconfiguration Request...
Waiting configuration Apply!!!
Restoring configuration...
EMMC ROM2/3 (Boot Partitions) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Wiping Card... Please do not touch it!!!
Done.
Please don't forget to repair extCSD from backup!!!
extCSD file...C:\Program Files\Z3X\EASYJTAG\Backups\VTU00M_1445412645_20140 404_1336.extcsd
Running:Repair extCSD...
Z3X EasyJtag Software ver. 1.3.4.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1103 mV
CMD Active Level:1433 mV
Writing...
Done!
Done.
Please don't forget to repair extCSD from backup!!!
Writing file...D:\BOX-SETUP\J-TAG\EASY-JTAG\9. Easy Jtag files\Samsung\GT-I9300\Dump\EMMC_ROM2_00000000_00200000.bin
Z3X EasyJtag Software ver. 1.3.4.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1103 mV
CMD Active Level:1433 mV
Writing 000000200000 bytes to 00000000 ...ROM2
Retry writing adress 0x00000000 (Attempt #1)...
Retry Fail !!!
Retry writing adress 0x00000000 (Attempt #2)...
Retry Fail !!!
Retry writing adress 0x00000000 (Attempt #3)...
Retry Fail !!!
Write Block Failed, Reason: DATA SND CRC Error
Writing file...D:\BOX-SETUP\J-TAG\EASY-JTAG\9. Easy Jtag files\Samsung\GT-I9300\Dump\EMMC_ROM1_00000000_20000000.bin
Z3X EasyJtag Software ver. 1.3.4.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1103 mV
CMD Active Level:1433 mV
Writing 000020000000 bytes to 00000000 ...ROM1
Retry writing adress 0x00000000 (Attempt #1)...
Retry Fail !!!
Retry writing adress 0x00000000 (Attempt #2)...
Retry Fail !!!
Retry writing adress 0x00000000 (Attempt #3)...
Retry Fail !!!
Write Block Failed, Reason: DATA SND CRC Error
  Reply With Quote
 
Page generated in 0.14099 seconds with 6 queries