GSM-Forum - View Single Post - mt65xx restart is hardware or not full supported

genci titi 2002 · 10-11-2014, 08:04

what is wrong is problem hardware or not full supported

Card found: S/N 4D19:0128
Chinese Miracle II [MTK module] v 1.02

Operation : Format FileSystem [ v1.02 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 18 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6582
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6582|8312_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 7001004D4D4330344758014B52CC1119
DA Stat : v4.2 on BBID : 0x87
DA Sent. Configure setting now ...
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0000 , [SAMSUNG] K9F5608Q0C
[NAND] : FLASH_DIE : 0000 0000 0000 0000 0000 0000 0000
[NAND] : FLASH_LEN : 0x00000000
INT RAM : 0x00000000
EXT RAM : 0x00000000
BOOT TYPE : DONE
SOC VERIFY : 00
Boot Ok!

Error read initial info , blank flash or wrong settings?

Operation Failed
Elapsed: 00:00:25
Reconnect Power/Cable!

10-11-2014, 08:04	#1 (permalink)
genci titi 2002 No Life Poster Join Date: Oct 2005 Location: TITI 2002 SERVIS CELULAR PG/AL Posts: 4,181 Member: 193804 Status: Offline Sonork: 100.1684818 Thanks Meter: 1,691	mt65xx restart is hardware or not full supported what is wrong is problem hardware or not full supported Card found: S/N 4D19:0128 Chinese Miracle II [MTK module] v 1.02 Operation : Format FileSystem [ v1.02 ] 1. Power Off Phone , Remove battery , Insert back 2. Insert USB cable. In some cases require hold BootKey Wait for phone... Phone found! [ 18 ] Sync... Inital regs read done Boot Info : BB_CPU_ID : 6582 BB_CPU_HW : CA01 BB_CPU_SW : 8A00 BB_CPU_SB : 0001 BB_CPU_NM : [MediaTek] MT6582\|8312_S00 Processing BROM stage SecCfgVal : 0x00000000 BromVersion : 0xFF BLVersion : 0x01 Preloader Status : Alive Processing DA stage DA Select done , sending NAND_ID : 00000000000000000000000000000000 eMMC_ID : 7001004D4D4330344758014B52CC1119 DA Stat : v4.2 on BBID : 0x87 DA Sent. Configure setting now ... NAND FlashIC initialized [NAND] : FLASH_VEN : 0x0000 , [SAMSUNG] K9F5608Q0C [NAND] : FLASH_DIE : 0000 0000 0000 0000 0000 0000 0000 [NAND] : FLASH_LEN : 0x00000000 INT RAM : 0x00000000 EXT RAM : 0x00000000 BOOT TYPE : DONE SOC VERIFY : 00 Boot Ok! Error read initial info , blank flash or wrong settings? Operation Failed Elapsed: 00:00:25 Reconnect Power/Cable!