| Running:SAMSUNG: eMMC firmware update...
Confirmed eMMC Part Number: KMVYL000LM
Z3X EasyJtag Software ver. 1.9.1.3
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0****************8, ,FW Ver.: 01.52
CMD Pullup Level:2114 mV
CMD Active Level:2495 mV
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Now Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0]!
Do it until progress bar is moving (20 sec timeout)!
Success!
eMMC firmware is updated now!
Please reconnect all eMMC lines before next operation!
Please don't forget to repair extCSD from backup!
Please don't forget to configure BOOT sizes!
Done.
You must select a valid extCSD file first!
extCSD file...C:\Program Files\Z3X\EASYJTAG\Backups\000000_ 537986070_20150303_1523.extcsd
Running:Repair extCSD...
Z3X EasyJtag Software ver. 1.9.1.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:2114 mV
CMD Active Level:2495 mV
Writing...
Done.
Z3X EasyJtag Software ver. 1.9.1.3
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0**************8, ,FW Ver.: 01.52
CMD Pullup Level:2114 mV
CMD Active Level:2495 mV
eMMC Device Information
EMMC CID : 15010056594C303000000000017A11AA
EMMC CSD : D02701320F5903FFF6DBFFEF8A404066
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 01/2014 Rev.0x0
EMMC NAME: VYL00 , S/N: 378
EMMC NAME (HEX): 56594C30302000
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: VYL00 _ 378_20150303_1526.extcsd
Done.
Checking NAND Image : D:\###gsm\###Flash - eeprom\##z3x\##EASY JTAG\###SAMSUNG\i\i9100\dump\Samsung_GT-i9100_model_dump_rom3_2mb.bin
File successefuly loaded!
Processing file...D:\###gsm\###Flash - eeprom\##z3x\##EASY JTAG\###SAMSUNG\i\i9100\dump\Samsung_GT-i9100_model_dump_rom3_2mb.bin
Z3X EasyJtag Software ver. 1.9.1.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:2114 mV
CMD Active Level:2495 mV
Input file : D:\###gsm\###Flash - eeprom\##z3x\##EASY JTAG\###SAMSUNG\i\i9100\dump\Samsung_GT-i9100_model_dump_rom3_2mb.bin
Writing 0000080000 bytes to 00000000 ...ROM3 (BOOT2 ROM)
Done. Write Speed: 558 kB/s
Checking NAND Image : D:\###gsm\###Flash - eeprom\##z3x\##EASY JTAG\###SAMSUNG\i\i9100\dump\Samsung_GT-i9100_model_dump_rom2_2mb.bin
File successefuly loaded!
Processing file...D:\###gsm\###Flash - eeprom\##z3x\##EASY JTAG\###SAMSUNG\i\i9100\dump\Samsung_GT-i9100_model_dump_rom2_2mb.bin
Z3X EasyJtag Software ver. 1.9.1.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:2114 mV
CMD Active Level:2495 mV
Input file : D:\###gsm\###Flash - eeprom\##z3x\##EASY JTAG\###SAMSUNG\i\i9100\dump\Samsung_GT-i9100_model_dump_rom2_2mb.bin
Writing 0000080000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Done. Write Speed: 289 kB/s
but after wrot Samsung_GT-i9100_model_dump_rom1_512mb.BIN from support i get again EMMC NAME: 00000 ...every time....is this dump file with bug or damaged? , can someone werify that?
Z3X EasyJtag Software ver. 1.9.1.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:2134 mV
CMD Active Level:2887 mV
Input file : D:\###gsm\###Flash - eeprom\##z3x\##EASY JTAG\###SAMSUNG\i\i9100\dump\Samsung_GT-i9100_model_dump_rom1_512mb.BIN
Writing 0020000000 bytes to 00000000 ...ROM1 (USER ROM)
Retry writing adress 0x00000000 (Attempt #1)...
Retry Fail!
Retry writing adress 0x00000000 (Attempt #2)...
Writing flash page stopped by user request
Done.
Last edited by kuli; 04-29-2015 at 13:51.
|