GSM-Forum - View Single Post - Step by step manual how to repair KMVYL000LM-B503 in pictures.

HaSHaM3001 · 05-10-2015, 09:42

EasyJtag Suite ver.: 1.9.1.2 / wxWidgets 3.1.0-W-U started.
Operating system ver.: Windows XP (build 2600, Service Pack 3).
Successfully connected to box on COM6
Box S/N: 00000000000000000, ,FW Ver.: 01.52
Box Working Mode: JTAG Box.
Box Drivers version: 3.0.0.0, are OK
Z3X Card Serial : 0000000000 , ver: 22
Z3X Card Activation [LG] : NOT ACTIVATED , ACTIVATE NOW
Z3X Card Activation [SAMS] : NOT ACTIVATED , ACTIVATE NOW
Z3X Card Activation [JTAG] : ACTIVATED
Z3X EasyJtag Software ver. 1.9.1.2
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 00000000000000000, ,FW Ver.: 01.52
CMD Pullup Level:2134 mV
CMD Active Level:2217 mV
eMMC Device Information
EMMC CID : 1501003030303030305620110726589C
EMMC CSD : 902701320F5903FFF6DBFFEF8A404022
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2005 Rev.0x56
EMMC NAME: 000000 , S/N: 537986854
EMMC NAME (HEX): 30303030303000
EMMC ROM1 (Main User Data) Capacity: 16384 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: 000000_ 537986854_20150401_0750.extcsd
Done.

Running:SAMSUNG: eMMC firmware update...
Confirmed eMMC Part Number: KMVTU000LM-B503
Z3X EasyJtag Software ver. 1.9.1.2
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 00000000000000000, ,FW Ver.: 01.52
CMD Pullup Level:2722 mV
CMD Active Level:2815 mV
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Success!
eMMC firmware is updated now!
Please reconnect all eMMC lines before next operation!
Please don't forget to repair extCSD from backup!
Please don't forget to configure BOOT sizes!
Done.

extCSD file...D:\All Mobaile Pinout\Box Tool\ATF\ATF JTAG\I9300\I9300_ATF_EMMC\S3_BOOT1_0x00000000_0x00 000FFF.bin
Running:Repair extCSD...
Z3X EasyJtag Software ver. 1.9.1.2
Skip loading eMMC Addon Firmware
CMD Pullup Level:2743 mV
CMD Active Level:2815 mV
Writing...
Done.

05-10-2015, 09:42	#19 (permalink)
HaSHaM3001 Freak Poster Join Date: Nov 2013 Location: SAUDIA ARABIA Posts: 182 Member: 2065652 Status: Offline Thanks Meter: 60	EasyJtag Suite ver.: 1.9.1.2 / wxWidgets 3.1.0-W-U started. Operating system ver.: Windows XP (build 2600, Service Pack 3). Successfully connected to box on COM6 Box S/N: 00000000000000000, ,FW Ver.: 01.52 Box Working Mode: JTAG Box. Box Drivers version: 3.0.0.0, are OK Z3X Card Serial : 0000000000 , ver: 22 Z3X Card Activation [LG] : NOT ACTIVATED , ACTIVATE NOW Z3X Card Activation [SAMS] : NOT ACTIVATED , ACTIVATE NOW Z3X Card Activation [JTAG] : ACTIVATED Z3X EasyJtag Software ver. 1.9.1.2 Loading eMMC Addon Firmware... IO: 2800 mV Box S/N: 00000000000000000, ,FW Ver.: 01.52 CMD Pullup Level:2134 mV CMD Active Level:2217 mV eMMC Device Information EMMC CID : 1501003030303030305620110726589C EMMC CSD : 902701320F5903FFF6DBFFEF8A404022 EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 05/2005 Rev.0x56 EMMC NAME: 000000 , S/N: 537986854 EMMC NAME (HEX): 30303030303000 EMMC ROM1 (Main User Data) Capacity: 16384 MB EMMC ROM2 (Boot Partition 1) Capacity: 512 kB EMMC ROM3 (Boot Partition 2) Capacity: 512 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD rev 1.5 (MMC 4.41) Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured. Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00. Backup saved: 000000_ 537986854_20150401_0750.extcsd Done. Running:SAMSUNG: eMMC firmware update... Confirmed eMMC Part Number: KMVTU000LM-B503 Z3X EasyJtag Software ver. 1.9.1.2 Loading eMMC Addon Firmware... IO: 2800 mV Box S/N: 00000000000000000, ,FW Ver.: 01.52 CMD Pullup Level:2722 mV CMD Active Level:2815 mV Setup firmware update mode, wait 2..30 sec... Success! Sending eMMC firmware... Success! Verifying eMMC firmware... Success! Flashing eMMC firmware... Success! Repairing eMMC CID... Success! eMMC firmware is updated now! Please reconnect all eMMC lines before next operation! Please don't forget to repair extCSD from backup! Please don't forget to configure BOOT sizes! Done. extCSD file...D:\All Mobaile Pinout\Box Tool\ATF\ATF JTAG\I9300\I9300_ATF_EMMC\S3_BOOT1_0x00000000_0x00 000FFF.bin Running:Repair extCSD... Z3X EasyJtag Software ver. 1.9.1.2 Skip loading eMMC Addon Firmware CMD Pullup Level:2743 mV CMD Active Level:2815 mV Writing... Done.