View Single Post
Old 09-10-2015, 08:34   #1 (permalink)
partycrasher131
Freak Poster
 
partycrasher131's Avatar
 
Join Date: Apr 2008
Location: World of technology
Posts: 367
Member: 749754
Status: Offline
Sonork: partycrasher131
Thanks Meter: 110
prestigio mt6583 stuck on logo cant read info cant read firmware cm2

Chinese Miracle II [MTK module] v 1.29


Operation : Check / Read Info [ v1.29 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 6 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 4D0001703830434D9A0D034723B06D94
DA Stat : v3.2 on BBID : 0x86
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0070 , OEM : 0100
[eMMC] : FLASH_INF : G80CM
[eMMC] : FLASH_CID : 7001004D4D43303847030D9A946DB023
[eMMC] : FLASH_LEN : 0x00000001D5400000
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Info read not done Erased phone or unsupported FlashIc?

Done!
Elapsed: 00:00:08
Reconnect Power/Cable!




Operation : Read Flash [ v1.29 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 6 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 4D0001703830434D9A0D034723B06D94
DA Stat : v3.2 on BBID : 0x86
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0070 , OEM : 0100
[eMMC] : FLASH_INF : G80CM
[eMMC] : FLASH_CID : 7001004D4D43303847030D9A946DB023
[eMMC] : FLASH_LEN : 0x00000001D5400000
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Conent now ...


after i try to read flash cm2 gives error of access violation
  Reply With Quote
 
Page generated in 0.14574 seconds with 6 queries