View Single Post
Old 09-27-2015, 13:20   #1 (permalink)
sofianegsm
Crazy Poster
 
Join Date: Jul 2005
Location: algeria
Age: 45
Posts: 53
Member: 161462
Status: Offline
Thanks Meter: 10
Acer e350 strange problem

hello.
i have acer e350 not accept any reset by hard or soft . all photos still exist after factory format by cm2mtk 1.32 . i think those photos are in system not in user data section . plz need solution .
Start at : [26/09/2015 / 20:46:25]
Operation : Check / Read Info [ v1.32 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 18 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6575
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : E201
BB_CPU_NM : [MediaTek] MT6575|MT6577_S00
Processing BROM stage
i2c Init : 00000000
SpeedSet : 0000
VChrgSet : 0x28 , BatStat : 0x82
WD Disable stat : 0x0000
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v7.1533.03
DA Stat : v3.2 on BBID : 0x84
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : M00SJ
[eMMC] : FLASH_CID : 1501004B4A5330304D03E5206F9D9F23
[eMMC] : FLASH_EXT : 00100000/00020000
[eMMC] : FLASH_LEN : 0x00000000E9000000
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Done!
Elapsed: 00:00:02
Reconnect Power/Cable!

Finish at : [26/09/2015 / 20:46:28]

Start at : [26/09/2015 / 20:46:49]
Operation : Format FileSystem [ v1.32 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 18 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6575
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : E201
BB_CPU_NM : [MediaTek] MT6575|MT6577_S00
Processing BROM stage
i2c Init : 00000000
SpeedSet : 0000
VChrgSet : 0x28 , BatStat : 0x82
WD Disable stat : 0x0000
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v7.1533.03
DA Stat : v3.2 on BBID : 0x84
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : M00SJ
[eMMC] : FLASH_CID : 1501004B4A5330304D03E5206F9D9F23
[eMMC] : FLASH_EXT : 00100000/00020000
[eMMC] : FLASH_LEN : 0x00000000E9000000
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:15
Reconnect Power/Cable!

Finish at : [26/09/2015 / 20:47:05]
  Reply With Quote
 
Page generated in 0.13152 seconds with 7 queries