When I try to remove virus it's says not supported. But with with NAND init mode P1-1 mode i can read info and read file. But that firmware also indetify by CM2 as a bad or corrupted file. I will post here all logs. Check what we can do...
All operation using NAND P1-1 and without it cant get success
Read info
Quote:
Start at : [3/11/2016 / 11:22:40 AM]
Operation : Check / Read Info [ v1.42 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 21 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : 009800BC009000660076001500010000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0096 , [TOSHIBA] TYBC0A111557KC
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0015 0001
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
DEV RID : F3270C47AA4ABA67AF27F566D1158370
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
[AP] : Initial info read Ok!
Brand : Symphony_Xplorer_W31
ProdName : Symphony_Xplorer_W31
ProdModel : E-tel i5c
Device : wt97055
AndroidVer: 4.2.2
MTKxCPU : MT6572
MTKxPRJ : SW_W97055A8_ETEL_I5C_M20_V004
SECURITY :
IMEI_SW [1] : 353833060015341
IMEI_SW [2] : 353833060015358
BTMAC Addr : 001EAD4A4ABE
WiFi MAC : 001EAD4A4ABF
Done!
Elapsed: 00:00:14
Reconnect Power/Cable!
Finish at : [3/11/2016 / 11:22:54 AM]
|
Read Firmware
Quote:
Start at : [3/10/2016 / 6:23:14 PM]
Operation : Read Flash [ v1.42 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 21 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : 009800BC009000660076001500010000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0096 , [TOSHIBA] TYBC0A111557KC
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0015 0001
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
DEV RID : F3270C47AA4ABA67AF27F566D1158370
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Reading Flash Content now ...
[Read Ok] : preloader_wt97055.bin
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : secro.img
[Read Ok] : logo.bin
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : usrdata.img
[ScatCFG] : MT6572 / V1.1.1 / wt97055 / NAND
FW Size : 317 MiB
Brand : Symphony_Xplorer_W31
ProdName : Symphony_Xplorer_W31
ProdModel : E-tel i5c
Device : wt97055
AndroidVer: 4.2.2
MTKxCPU : MT6572
MTKxPRJ : SW_W97055A8_ETEL_I5C_M20_V004
Android Info saved
Scatter saved to : C:\mtk temp\MT6572_NAND_Symphony_Xplorer_W31__E-tel i5c__wt97055__4.2.2__SW_W97055A8_ETEL_I5C_M20_V004
Done!
Elapsed: 00:02:43
|
Remove virus
Quote:
Start at : [3/10/2016 / 6:26:28 PM]
Operation : Remove Viruses [SmartAV] [ v1.42 ]
SmartAV Conf : 100/80/2000
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 21 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : 009800BC009000660076001500010000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0096 , [TOSHIBA] TYBC0A111557KC
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0015 0001
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
DEV RID : F3270C47AA4ABA67AF27F566D1158370
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
NAND Flash not supported yet!
Done!
Elapsed: 00:00:10
|
Then I tried to flash it with factory file. But when I gonna select scatter I cant see it using firmware open window. Like another file type it cant see through that.
When I select that i red firmware from this phone it said....
Quote:
|
Unsupported Yet( or bad ) file selected!
|
I have few questions
1. If can read firmware why we cant remove virus?
2. Why cant see factory firmware scatter file through firmware window of CM2?
3. Firmware read success. But cant use it. Why?
4. Look like there is no EMMC. Just NAND. How can effect it to our flashing and other operations?
Sorry for long thread. But If you can please explain these shortly. I don't wanna miss anything that we can do using CM2