| see my post
3X EasyJtag Software ver. 2.0.7.6
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0B00A018B9D80701, ,FW Ver.: 01.52
CMD Pullup Level:1258 mV
CMD Active Level:2186 mV
HiPower™ mode is ON!
eMMC Device Information
EMMC CID : 110100343030303733002996114DB2FC
EMMC CSD : D07E00320F5903FFFFFFFFE78A4000D0
EMMC Manufacturer ID: 0011 , OEM ID: 0100
EMMC Date: 11/2015 Rev.0x0
EMMC NAME: 400073 , S/N: 697700685
EMMC NAME (HEX): 34303030373300
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.7 (MMC 5.0)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x00
Backup saved: 400073_ 697700685_20160402_1521.extcsd
Done.
Processing file...C:\Users\ALiraza\Desktop\New folder\ROM2_J700HXXU1APA3_KLMAG2GEAC_sboot.bin
Processing file...C:\Users\ALiraza\Desktop\New folder\ROM2_J700HXXU1APA3_KLMAG2GEAC_sboot.bin
Processing file...C:\Users\ALiraza\Desktop\New folder\ROM3_J700HXXU1APA3_KLMAG2GEAC_cm.bin
extCSD Are not selected , skip writing extCSD
Z3X EasyJtag Software ver. 2.0.7.6
Skip loading eMMC Addon Firmware
CMD Pullup Level:1258 mV
CMD Active Level:2186 mV
Input file : C:\Users\ALiraza\Desktop\New folder\ROM2_J700HXXU1APA3_KLMAG2GEAC_sboot.bin
Writing 0000400000 bytes to 00000000 ...ROM1 (USER ROM)
Full Verify Enabled!
Done. Write Speed: 449 kB/s
Z3X EasyJtag Software ver. 2.0.7.6
Skip loading eMMC Addon Firmware
CMD Pullup Level:1258 mV
CMD Active Level:2186 mV
Input file : C:\Users\ALiraza\Desktop\New folder\ROM2_J700HXXU1APA3_KLMAG2GEAC_sboot.bin
Writing 0000400000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Full Verify Enabled!
Done. Write Speed: 379 kB/s
Z3X EasyJtag Software ver. 2.0.7.6
Skip loading eMMC Addon Firmware
CMD Pullup Level:1258 mV
CMD Active Level:2186 mV
Input file : C:\Users\ALiraza\Desktop\New folder\ROM3_J700HXXU1APA3_KLMAG2GEAC_cm.bin
Writing 0000400000 bytes to 00000000 ...ROM3 (BOOT2 ROM)
Full Verify Enabled!
Done. Write Speed: 380 kB/s
every thing is done but only sec-spc210 test b/d driver needed soualtion badly |