GSM-Forum - View Single Post

Octopus box · 10-19-2016, 15:25

Medusa PRO v.1.2.2 is out!

Also added support for HTC Desire 601, LG Nexus 5x, Samsung Galaxy J3, Galaxy S3 Progre, Lenovo IdeaTab!

Medusa PRO v.1.2.2 Release Notes:

- Added support for the following models via eMMC:

HTC Desire 601 - Read/Write/Erase, Easy Repair, Partition Manager, Constructor for Repair Files

LG H790 - Read/Write/Erase, Easy Repair, Partition Manager, Constructor for Repair Files

Samsung SM-J320H - Read/Write/Erase, Easy Repair, Partition Manager, Constructor for Repair Files

Samsung SCL21 - Read/Write/Erase, Easy Repair, Partition Manager, Constructor for Repair Files

Lenovo A3000F - Read/Write/Erase, Easy Repair, Factory Repair (via scatter), Constructor for Repair Files

- Updated help and pinouts in Smart Repair File for LG MS345 (please re-download SRF).

- Improved showing of progress status while writing scatter firmware of MediaTek based devices.

- Fixed “Cancel” operation for process of writing scatter firmware.

- Improvements in "Content Extractor":
Improved process of searching contacts

Improved exporting of contacts - added UTF-8 support while exporting into text formats

- Some GUI changes.

- Firmware of Medusa Pro Box has been updated! To update the firmware, please connect the box and only then run the Software. Also you can update box firmware via “Update Box Firmware” button at “Welcome” tab in Software.

- All pinouts and Repair procedures are described in Software manuals ("Help" button in Software).

How to Repair box firmware, if box not detected by PC and Box status in Medusa Pro Software is “Not connected” after firmware updating.

To repair box firmware, do the next:
Disconnect all Boxes and other devices from PC.

Run the Medusa Pro Software.

Open Control Panel -> Device Manager.

Open (disassemble) Medusa Pro box.

Connect the box to PC via USB cable.

Heat up IC U6 (smaller square MCU) on PCB using hot air gun or soldering iron at 150 °C (300 °F) for a few seconds till “libusb-win32 devices / HSJTAG V0x100” device appears in PC Device Manager and Box status in Medusa Pro Software becomes “Connected”. Also LED’s will start blinking at that moment.

Go to “Welcome” tab in Medusa Pro Software and press “Update Box Firmware” button.

Box firmware should be updated to version 1.13.

Note! After repairing box firmware you shouldn’t use previous versions of Medusa Pro Software, please always use the latest actual software version.

Medusa - Ultimate Breakthrough in the Phone Repair!

Download Medusa PRO Software v.1.2.2

________________________________________
WBR,
Medusa Box Team

10-19-2016, 15:25	#22 (permalink)
Octopus box Product Supporter Join Date: Oct 2009 Location: Romania, Bucharest Posts: 99,835 Member: 1146942 Status: Offline Sonork: 100.1587278 Thanks Meter: 27,411	V1.2.2 - added support for HTC Desire 601, LG Nexus 5x and more! Medusa PRO v.1.2.2 is out! Also added support for HTC Desire 601, LG Nexus 5x, Samsung Galaxy J3, Galaxy S3 Progre, Lenovo IdeaTab! Medusa PRO v.1.2.2 Release Notes: - Added support for the following models via eMMC: HTC Desire 601 - Read/Write/Erase, Easy Repair, Partition Manager, Constructor for Repair Files LG H790 - Read/Write/Erase, Easy Repair, Partition Manager, Constructor for Repair Files Samsung SM-J320H - Read/Write/Erase, Easy Repair, Partition Manager, Constructor for Repair Files Samsung SCL21 - Read/Write/Erase, Easy Repair, Partition Manager, Constructor for Repair Files Lenovo A3000F - Read/Write/Erase, Easy Repair, Factory Repair (via scatter), Constructor for Repair Files - Updated help and pinouts in Smart Repair File for LG MS345 (please re-download SRF). - Improved showing of progress status while writing scatter firmware of MediaTek based devices. - Fixed “Cancel” operation for process of writing scatter firmware. - Improvements in "Content Extractor": Improved process of searching contacts Improved exporting of contacts - added UTF-8 support while exporting into text formats - Some GUI changes. - Firmware of Medusa Pro Box has been updated! To update the firmware, please connect the box and only then run the Software. Also you can update box firmware via “Update Box Firmware” button at “Welcome” tab in Software. - All pinouts and Repair procedures are described in Software manuals ("Help" button in Software). How to Repair box firmware, if box not detected by PC and Box status in Medusa Pro Software is “Not connected” after firmware updating. To repair box firmware, do the next: Disconnect all Boxes and other devices from PC. Run the Medusa Pro Software. Open Control Panel -> Device Manager. Open (disassemble) Medusa Pro box. Connect the box to PC via USB cable. Heat up IC U6 (smaller square MCU) on PCB using hot air gun or soldering iron at 150 °C (300 °F) for a few seconds till “libusb-win32 devices / HSJTAG V0x100” device appears in PC Device Manager and Box status in Medusa Pro Software becomes “Connected”. Also LED’s will start blinking at that moment. Go to “Welcome” tab in Medusa Pro Software and press “Update Box Firmware” button. Box firmware should be updated to version 1.13. Note! After repairing box firmware you shouldn’t use previous versions of Medusa Pro Software, please always use the latest actual software version. Medusa - Ultimate Breakthrough in the Phone Repair! Download Medusa PRO Software v.1.2.2 ________________________________________ WBR, Medusa Box Team Last edited by Octopus box; 10-28-2016 at 15:10.