Qmobile Z14 dead revived succesfully.
Code:
Scatter Load Ok , BaseBand : MT6755 , Project : gionee6755_66_m , Storage : EMMC
Files found : 16 , Set to Flash : 15
Ready to Flash!
Operation : Flash [ v1.58 ]
======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 15 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6755
BB_CPU_NME : [MediaTek] Helio[P10]|MT6755_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
DAgent configured successfully
Connection agent : PRELOADER
DRAM already initialized by Preloader
Link with DAgent established
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM41X
[eMMC] : FLASH_CID : 150100525831344D42071AC5DA4BA31F
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x0000000747C00000
[eMMC] : FLASH_UCP : 29820 MiB [eMMC 32 GiB]
DEV RID : 0xFB5A6F19B4E7BAF4512191E86A6FC048
INT RAM : 0x00000000
EXT RAM : 0x80000000 [2 GiB]
[NAND] : FLASH : NOT INSTALLED
[UFSM] : FLASH : NOT INSTALLED
[HSUSB] : MODE : HIGH-SPEED
Boot Ok!
ScatCFG : BaseBand : MT6755 , Project : gionee6755_66_m , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled
M67BL : Check eMMC compatibility
M67BL : eMMC supported by BootLoader!
Selected forced PMT update
Build new PMT ...
Update Primary ...
Update Mirror ...
PMT update Ok!
M67BL : Flash Erase
Total blocks to Erase : 4
Erase : 0x0000000000008000-0x0000000005BC0000
Erase : 0x0000000007000000-0x0000000000040000
Erase : 0x0000000007800000-0x0000000002C00000
Erase : 0x000000000A900000-0x00000001DE700000
Flash Erase Done, time used : 00:00:01
Processing : Writing all Flash Files
Flash Partition : PRELOADER
Flash PLC
Image Flash Ok
Flash Partition : RECOVERY
Image Flash Ok
Flash Partition : MD1IMG
Image Flash Ok
Flash Partition : MD1DSP
Image Flash Ok
Flash Partition : MD1ARM7
Image Flash Ok
Flash Partition : MD3IMG
Image Flash Ok
Flash Partition : LK
Image Flash Ok
Flash Partition : LK2
Image Flash Ok
Flash Partition : BOOT
Image Flash Ok
Flash Partition : LOGO
Image Flash Ok
Flash Partition : TEE1
Image Flash Ok
Flash Partition : TEE2
Image Flash Ok
Flash Partition : SECRO
Image Flash Ok
Flash Partition : SYSTEM
Image Flash Ok
Flash Partition : CACHE
Image Flash Ok
Flash Partition : USERDATA
Image Flash Ok
Flash Write Done, time used : 00:02:31
Done!
Elapsed: 00:03:16
Reconnect Power/Cable!
But one think I dont understand why CM2 not verify after flash.Mr JAYDI sir plz tell me about this and in settings VERIFY option is selected.