View Single Post
Old 03-08-2018, 14:21   #1 (permalink)
Khan Bhaie
Freak Poster
 
Khan Bhaie's Avatar
 
Join Date: Oct 2014
Posts: 250
Member: 2276949
Status: Offline
Thanks Meter: 77
SPD Flashing Problem

I Have Clone Infinix X600-LTE SPD7731 With Unfortunately YouTube Has Stopped.Factory Reset But Again Same Error So I Read Flash From Working Phone and Flashed But Got Error In Flashing Now Mobile Is Dead Not Flashing Even With Own Backup

Read Flash
Code:
Operation : Read FullFlash [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key 
3. Insert cable

 ====  Wait for phone...

Phone found! [ 93 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!

[FW_READER] : Prepare Ok!
- > Wait phone connected ... 

Phone found! [ 93 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

- > Wait phone connected ... 

Phone found! [ 93 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Model Name  : X600-LTE
Model Brand : X600-LTE
Model Device: X600-LTE
AndrVersion : 5.1
BaseBand CPU: X600-LTE
Project Ver : X600-H533-A1-L-20151214
Model Ext   : X600-LTE

[Read Mode] : HSUSB : 0x3000

[FW_READER] : Reading Firmware Now ... 

[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731g_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc8830g_modem_CP2_WCN_14D_W15.31.1_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_480x854.bin
[Read Ok] : logo1.bin
[Read Ok] : logo2.bin
[Read Ok] : logo3.bin
[Read Ok] : logo4.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Build Ok] : userdata.img

AndroidInfo created
Firmware Size : 1433 MiB
Saved to : C:\InfinityBox\CM2SPD\Flash\X600-LTE_X600-LTE_5.1_X600-H533-A1-L-20151214_X600-LTE\
Done!

Elapsed: 00:06:36
EMMC Test
Code:
Operation : FlashIC ReadOnly/BadBlock Test [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key 
3. Insert cable

 ====  Wait for phone...

Phone found! [ 93 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ... 
Detected eMMC Flash , Structure detect Ok!

Prepare test data ... 
Test flow #0 ... 
Test flow passed!
Test flow #1 ... 
Test flow passed!
Test flow #2 ... 
Test flow passed!
Test flow #3 ... 
Test flow passed!
Test flow #4 ... 
Test flow passed!
Test flow #5 ... 
Test flow passed!

Finalize Ok!
Test passed successfully!

Elapsed: 00:00:26
Flashing Error
Code:
Operation : Flash [ v1.27 ]

======= Flash
Files set for flashing : 
[ MCU ] : Infinix X6OO SPD.pac
CRVersion  : BP_R1.0.0
PacCPUinfo : SC77xx
PacVersion : Infinix X6OO SPD
File : Infinity_fdl1.bin
File : Infinity_fdl2.bin
File : nvitem_w.bin
File : nvitem_wcn.bin
File : prodnv.img
File : u-boot-spl-16k.bin
File : sc7731g_CP0_modem.bin
File : DSP_DM_Gx.bin
File : sc8830g_modem_CP2_WCN_14D_W15.31.1_Release.bin
File : logo_480x854.bin
File : boot.img
File : system.img
File : cache.img
File : recovery.img
File : userdata.img
File : u-boot.bin

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key 
3. Insert cable

 ====  Wait for phone...

Phone found! [ 93 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
PMTManager : Load 0x1A records
PMTManager : PMT Update Ok!
Flashing now

[FlashProc] : CODE  
Current ID : PRODNV
Current File : prodnv.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : ERASEUBOOT
Current Part : uboot
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : FLASH
Current Part : wruntimenv1
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : FLASH_WCN
Current Part : wcnruntimenv1
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : ERASEMISC
Current Part : misc
[FlashProc] : Ok!

[FlashProc] : BOOTCODE
Current ID   : SPLLOADER
Current File : u-boot-spl-16k.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : MODEM_W
Current File : sc7731g_CP0_modem.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : DSP_W
Current File : DSP_DM_Gx.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : MODEM_WCN
Current File : sc8830g_modem_CP2_WCN_14D_W15.31.1_Release.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : BOOTLOGO
Current File : logo_480x854.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : BOOT
Current File : boot.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : SYSTEM
Current File : system.img
Flashing now ... 
[FlashProc] : Error with code 0x00037E008A0000FF757E

Elapsed: 00:00:11
Code:
Operation : Check/Read Info [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key 
3. Insert cable

 ====  Wait for phone...

Phone found! [ 93 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Unknown structure detected! Check correct model selection!

Elapsed: 00:00:28
Code:
Operation : Flash [ v1.27 ]

======= Flash
Files set for flashing : 
[ MCU ] : X600-LTE_X600-LTE_5.1_X600-H533-A1-L-20151214_X600-LTE.pac
CRVersion  : BP_R1.0.0
PacCPUinfo : SC77xx
PacVersion : SC7731_eMMC_X600-LTE_5.1_X600-H533-A1-L-20151214_X600-LT_INFINITY-BOX
File : Infinity_fdl1.bin
File : Infinity_fdl2.bin
File : nvitem_w.bin
File : nvitem_wcn.bin
File : prodnv.img
File : u-boot-spl-16k.bin
File : sc7731g_CP0_modem.bin
File : DSP_DM_Gx.bin
File : sc8830g_modem_CP2_WCN_14D_W15.31.1_Release.bin
File : logo_480x854.bin
File : boot.img
File : system.img
File : cache.img
File : recovery.img
File : userdata.img
File : u-boot.bin

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key 
3. Insert cable

 ====  Wait for phone...

Phone found! [ 93 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
PMTManager : Load 0x1A records
PMTManager : PMT Update Ok!
Flashing now

[FlashProc] : CODE  
Current ID : PRODNV
Current File : prodnv.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : ERASEUBOOT
Current Part : uboot
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : FLASH
Current Part : wruntimenv1
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : FLASH_WCN
Current Part : wcnruntimenv1
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : ERASEMISC
Current Part : misc
[FlashProc] : Ok!

[FlashProc] : BOOTCODE
Current ID   : SPLLOADER
Current File : u-boot-spl-16k.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : MODEM_W
Current File : sc7731g_CP0_modem.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : DSP_W
Current File : DSP_DM_Gx.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : MODEM_WCN
Current File : sc8830g_modem_CP2_WCN_14D_W15.31.1_Release.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : BOOTLOGO
Current File : logo_480x854.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : BOOT
Current File : boot.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : SYSTEM
Current File : system.img
Flashing now ... 
[FlashProc] : Error with code 0x00027E00800000FF7F7E

Elapsed: 00:10:06
Code:
Operation : Flash [ v1.27 ]

======= Flash
Files set for flashing : 
[ MCU ] : SC77xx Infinity Package

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key 
3. Insert cable

 ====  Wait for phone...

Phone found! [ 131 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Error Init FL mode!



PMTManager : Load 0x1A records
Any Solution???
  Reply With Quote
 
Page generated in 0.17401 seconds with 6 queries