[rico_deep]

Bug on eMMC HW Partition

Compression is ON
Z3X EasyJtag Software ver. 2.9.0.2
Loading eMMC GEN1 Firmware... IO: 2800 mV
Box S/N: TresMarias, ,FW Ver.: 01.62
CMD Pullup Level:1794 mV
CMD Active Level:2289 mV
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------

EMMC CID : 90014A48344732611101B4A3EC8BA242
EMMC CSD : D02701320F5903FFFFFFFFEF8A4040D2
EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 10/2015 Rev.0x1
EMMC NAME: H4G2a , S/N: 3030641803
EMMC NAME (HEX): 48344732612000
EMMC ROM1 (Main User Data) Capacity: 3728 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: H4G2a _3030641803_20180412_1153.extcsd
Done.

Running:JEDEC: Partitions config burn...
Z3X EasyJtag Software ver. 2.9.0.2
Skip loading eMMC Addon Firmware
CMD Pullup Level:1794 mV
CMD Active Level:2289 mV
Box IO Level:2800 mV
CLK Rate:21000 kHz
GP Multiplier: 800000, 8192 Kb, 8Mb
Partition configuration:
No enhanced user data area
User partition write reliability: off
No GP1 partition
GP1 write reliability: on
No GP2 partition
GP2 write reliability: on
No GP3 partition
GP3 write reliability: on
No GP4 partition
GP4 write reliability: on
All GP Partitions are 0 set size of at least one GP Partition
HW Parts Config Fail.

Done on Easy Jtag eMMC Tool Suite V1.4.9.0

CMD Pullup Level: 1773 mV
CMD Active Level: 2279 mV
EMMC Device Information :
EMMC CID: 90014A48344732611101B4A3EC8BA242
EMMC CSD: D02701320F5903FFFFFFFFEF8A4040D2
EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2a , EMMC NAME (HEX): 483447326100 , S/N: B4A3EC8B , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 10/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2a_B4A3EC8B_20180412_115419.extcsd
EMMC Init completed.

Operation: Changing GP sizes (final write) ...

GP1 size: 0 MB , WR_REL: 1 , ENH 1
GP1 size: 0 MB , WR_REL: 1 , ENH 0
GP1 size: 0 MB , WR_REL: 1 , ENH 0
GP1 size: 0 MB , WR_REL: 1 , ENH 0

Successfully

Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0] to finalize operation

After reconnect, make sure that the size of ROM1 has been changed.