[kopito]

4/16/2018 12:27:08 PM> Looking for EasyJTAG box...
4/16/2018 12:27:08 PM> EasyJTAG API ver. 2022
4/16/2018 12:27:08 PM> Setting IO Levels to 1.8V
4/16/2018 12:27:08 PM> Setting frequence to 24 Mhz
4/16/2018 12:27:08 PM> EasyJTAG Box Serial = 7B3FF048XXXX
4/16/2018 12:27:09 PM> Setting interface to EasyJtag2/ISP_HiPower
4/16/2018 12:27:09 PM> Setting bus width to 1 Bit
4/16/2018 12:27:09 PM> HiPower mode is ON
4/16/2018 12:27:09 PM> Setting frequence to 24 Mhz
4/16/2018 12:27:09 PM> CMD Pullup Level: 1727 mV
4/16/2018 12:27:09 PM> CMD Active Level: 1826 mV
4/16/2018 12:27:09 PM> eMMC Init returned = 0
4/16/2018 12:27:09 PM> EMMC Device Information :
4/16/2018 12:27:09 PM> EMMC CID: FE014E50314A39354B1350AD4D78523D
4/16/2018 12:27:09 PM> EMMC CSD: D07F01320F5913FFFFFFFFEF924000A3
4/16/2018 12:27:09 PM> EMMC Manufacture Name: MICRON , EMMC NAME: P1J95K , EMMC NAME (HEX): 50314A39354B , S/N: 50AD4D78 , rev. 0x13
4/16/2018 12:27:09 PM> EMMC Manufacture ID: 0xFE , OEM ID: 0x4E , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015
4/16/2018 12:27:09 PM> EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)
4/16/2018 12:27:09 PM> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
4/16/2018 12:27:09 PM> EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
4/16/2018 12:27:09 PM> EMMC Permanent Write Protection: No
4/16/2018 12:27:09 PM> EMMC Temporary Write Protection: No
4/16/2018 12:27:09 PM> Extended CSD Information :
4/16/2018 12:27:09 PM> Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
4/16/2018 12:27:09 PM> Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
4/16/2018 12:27:09 PM> Boot Bus Config: 0x00 , width 1bit
4/16/2018 12:27:09 PM> H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
4/16/2018 12:27:09 PM> Supported partition features [PARTITIONING_SUPPORT]: 0x07
4/16/2018 12:27:09 PM> Device supports partitioning features
4/16/2018 12:27:09 PM> Device can have enhanced technological features in partitions and user data area
4/16/2018 12:27:09 PM> Device can have extended partitions attribute
4/16/2018 12:27:09 PM> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
4/16/2018 12:27:09 PM> Backup saved: P1J95K_50AD4D78_20180416_122709.extcsd
4/16/2018 12:27:09 PM> EMMC Init completed.
4/16/2018 12:27:09 PM>
4/16/2018 12:27:10 PM> Opening file: C:\Users\kopito\Desktop\COREPRIMELTE_EUR_OPEN.pit
4/16/2018 12:27:10 PM>
4/16/2018 12:27:10 PM> Pit: COREPRIMELTE_EUR_OPEN.pit
4/16/2018 12:27:10 PM> Entry count: 31
4/16/2018 12:27:10 PM>
4/16/2018 12:27:10 PM> The size of the last section has been updated
4/16/2018 12:30:06 PM> Selected file: C:\Users\kopito\Desktop\SM-G360F_1_20170615153000_7e184c4f8n_fac\BL_G360FXXS1 BQD2_CL953652_QB13119115_REV00_user_low_ship_MULTI _CERT.tar.md5
4/16/2018 12:30:06 PM>
4/16/2018 12:30:06 PM> BL_G360FXXS1BQD2_CL953652_QB13119115_REV00_user_lo w_ship_MULTI_CERT.tar.md5
4/16/2018 12:30:06 PM> The list of files in the firmware:
4/16/2018 12:30:06 PM> aboot.mbn
4/16/2018 12:30:06 PM> sbl1.mbn
4/16/2018 12:30:06 PM> rpm.mbn
4/16/2018 12:30:06 PM> tz.mbn
4/16/2018 12:30:06 PM> hyp.mbn
4/16/2018 12:30:06 PM> non-hlos.bin
4/16/2018 12:30:06 PM> sec.dat
4/16/2018 12:30:06 PM>
4/16/2018 12:30:08 PM> Selected file: C:\Users\kopito\Desktop\SM-G360F_1_20170615153000_7e184c4f8n_fac\AP_G360FXXS1 BQD2_CL953652_QB13119115_REV00_user_low_ship_MULTI _CERT.tar.md5
4/16/2018 12:30:08 PM> AP_G360FXXS1BQD2_CL953652_QB13119115_REV00_user_lo w_ship_MULTI_CERT.tar.md5
4/16/2018 12:30:08 PM> The list of files in the firmware:
4/16/2018 12:30:08 PM> boot.img
4/16/2018 12:30:08 PM> recovery.img
4/16/2018 12:30:08 PM> system.img.ext4
4/16/2018 12:30:08 PM> persist.img.ext4
4/16/2018 12:30:08 PM>
4/16/2018 12:30:11 PM> Selected file: C:\Users\kopito\Desktop\SM-G360F_1_20170615153000_7e184c4f8n_fac\CP_G360FXXS1 BQA2_REV00_CL1981445_QB5541753.tar.md5
4/16/2018 12:30:11 PM> CP_G360FXXS1BQA2_REV00_CL1981445_QB5541753.tar.md5
4/16/2018 12:30:11 PM> The list of files in the firmware:
4/16/2018 12:30:11 PM> modem.bin
4/16/2018 12:30:11 PM>
4/16/2018 12:30:13 PM> Selected file: C:\Users\kopito\Desktop\SM-G360F_1_20170615153000_7e184c4f8n_fac\CSC_MEO_G360 FMEO1BOJ1_CL823270_QB6491466_REV00_user_low_ship_M ULTI_CERT.tar.md5
4/16/2018 12:30:13 PM> CSC_MEO_G360FMEO1BOJ1_CL823270_QB6491466_REV00_use r_low_ship_MULTI_CERT.tar.md5
4/16/2018 12:30:13 PM> The list of files in the firmware:
4/16/2018 12:30:13 PM> coreprimelte_eur_open_hidden40m.pit
4/16/2018 12:30:13 PM> cache.img.ext4
4/16/2018 12:30:13 PM> hidden.img.ext4
4/16/2018 12:30:13 PM>
4/16/2018 12:30:15 PM> Looking for EasyJTAG box...
4/16/2018 12:30:15 PM> EasyJTAG API ver. 2022
4/16/2018 12:30:15 PM> Setting IO Levels to 1.8V
4/16/2018 12:30:15 PM> Setting frequence to 24 Mhz
4/16/2018 12:30:15 PM> EasyJTAG Box Serial = 7B3FFXXXX
4/16/2018 12:30:15 PM> EasyJTAG Box Firmware = 2.22
4/16/2018 12:30:15 PM> Setting interface to EasyJtag2/ISP_HiPower
4/16/2018 12:30:15 PM> Setting bus width to 1 Bit
4/16/2018 12:30:15 PM> HiPower mode is ON
4/16/2018 12:30:15 PM> Setting frequence to 24 Mhz
4/16/2018 12:30:15 PM> CMD Pullup Level: 1660 mV
4/16/2018 12:30:15 PM> CMD Active Level: 1804 mV
4/16/2018 12:30:15 PM> eMMC Init returned = 0
4/16/2018 12:30:15 PM> EMMC Device Information :
4/16/2018 12:30:15 PM> EMMC CID: FE014E50314A39354B1350AD4D78523D
4/16/2018 12:30:15 PM> EMMC CSD: D07F01320F5913FFFFFFFFEF924000A3
4/16/2018 12:30:15 PM> EMMC Manufacture Name: MICRON , EMMC NAME: P1J95K , EMMC NAME (HEX): 50314A39354B , S/N: 50AD4D78 , rev. 0x13
4/16/2018 12:30:15 PM> EMMC Manufacture ID: 0xFE , OEM ID: 0x4E , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015
4/16/2018 12:30:15 PM> EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)
4/16/2018 12:30:15 PM> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
4/16/2018 12:30:15 PM> EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
4/16/2018 12:30:15 PM> EMMC Permanent Write Protection: No
4/16/2018 12:30:16 PM> EMMC Temporary Write Protection: No
4/16/2018 12:30:16 PM> Extended CSD Information :
4/16/2018 12:30:16 PM> Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
4/16/2018 12:30:16 PM> Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
4/16/2018 12:30:16 PM> Boot Bus Config: 0x00 , width 1bit
4/16/2018 12:30:16 PM> H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
4/16/2018 12:30:16 PM> Supported partition features [PARTITIONING_SUPPORT]: 0x07
4/16/2018 12:30:16 PM> Device supports partitioning features
4/16/2018 12:30:16 PM> Device can have enhanced technological features in partitions and user data area
4/16/2018 12:30:16 PM> Device can have extended partitions attribute
4/16/2018 12:30:16 PM> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
4/16/2018 12:30:16 PM> Backup saved: P1J95K_50AD4D78_20180416_123016.extcsd
4/16/2018 12:30:16 PM> EMMC Init completed.
4/16/2018 12:30:16 PM>
4/16/2018 12:30:16 PM> Operation: Write by vendor (Samsung)
4/16/2018 12:30:16 PM>
4/16/2018 12:30:16 PM> Creating GPT-partitioninig
4/16/2018 12:30:16 PM> Writing PIT at address: 000000004400
4/16/2018 12:30:16 PM> GPT-partitioning done
4/16/2018 12:30:16 PM>
4/16/2018 12:30:16 PM> Unpacking file: non-hlos.bin
4/16/2018 12:30:17 PM> Unpacking file: modem.bin
4/16/2018 12:30:17 PM> Unpacking file: sbl1.mbn
4/16/2018 12:30:17 PM> Unpacking file: aboot.mbn
4/16/2018 12:30:17 PM> Unpacking file: rpm.mbn
4/16/2018 12:30:17 PM> Unpacking file: tz.mbn
4/16/2018 12:30:17 PM> Unpacking file: hyp.mbn
4/16/2018 12:30:17 PM> Unpacking file: sec.dat
4/16/2018 12:30:17 PM> Unpacking file: boot.img
4/16/2018 12:30:17 PM> Unpacking file: recovery.img
4/16/2018 12:30:18 PM> Unpacking file: persist.img.ext4
4/16/2018 12:30:18 PM> Unpacking file: system.img.ext4
4/16/2018 12:30:45 PM> Unpacking file: cache.img.ext4
4/16/2018 12:30:45 PM> Unpacking file: hidden.img.ext4
4/16/2018 12:30:45 PM>
4/16/2018 12:30:45 PM> Partition name: APNHLOS
4/16/2018 12:30:45 PM> Filename: non-hlos.bin , Offset: 000000400000 , filesize: 13485824 bytes
4/16/2018 12:30:45 PM> eMMC switching to ROM1
4/16/2018 12:30:46 PM> Erasing partition...
4/16/2018 12:30:47 PM> Writing partition...
4/16/2018 12:30:53 PM> Done writing partition. Write speed: 2496.75 KB/s
4/16/2018 12:30:53 PM> Partition name: MODEM
4/16/2018 12:30:53 PM> Filename: modem.bin , Offset: 000001300000 , filesize: 46532352 bytes
4/16/2018 12:30:53 PM> eMMC switching to ROM1
4/16/2018 12:30:53 PM> Erasing partition...
4/16/2018 12:30:55 PM> Writing partition...
4/16/2018 12:31:13 PM> Done writing partition. Write speed: 2574.31 KB/s
4/16/2018 12:31:13 PM> Partition name: SBL1
4/16/2018 12:31:13 PM> Filename: sbl1.mbn , Offset: 000004C70000 , filesize: 280468 bytes
4/16/2018 12:31:13 PM> eMMC switching to ROM1
4/16/2018 12:31:13 PM> Erasing partition...
4/16/2018 12:31:13 PM> Writing partition...
4/16/2018 12:31:14 PM> Done writing partition. Write speed: 1491.67 KB/s
4/16/2018 12:31:14 PM> Partition name: ABOOT
4/16/2018 12:31:14 PM> Filename: aboot.mbn , Offset: 000004CF8000 , filesize: 1041384 bytes
4/16/2018 12:31:14 PM> eMMC switching to ROM1
4/16/2018 12:31:14 PM> Erasing partition...
4/16/2018 12:31:14 PM> Writing partition...
4/16/2018 12:31:15 PM> Done writing partition. Write speed: 2263.56 KB/s
4/16/2018 12:31:15 PM> Partition name: RPM
4/16/2018 12:31:15 PM> Filename: rpm.mbn , Offset: 000004EF8000 , filesize: 187764 bytes
4/16/2018 12:31:15 PM> eMMC switching to ROM1
4/16/2018 12:31:15 PM> Erasing partition...
4/16/2018 12:31:16 PM> Writing partition...
4/16/2018 12:31:16 PM> Done writing partition. Write speed: 1332.03 KB/s
4/16/2018 12:31:16 PM> Partition name: QSEE
4/16/2018 12:31:16 PM> Filename: tz.mbn , Offset: 000004F78000 , filesize: 520588 bytes
4/16/2018 12:31:16 PM> eMMC switching to ROM1
4/16/2018 12:31:16 PM> Erasing partition...
4/16/2018 12:31:17 PM> Writing partition...
4/16/2018 12:31:17 PM> Done writing partition. Write speed: 2200.97 KB/s
4/16/2018 12:31:17 PM> Partition name: QHEE
4/16/2018 12:31:17 PM> Filename: hyp.mbn , Offset: 000004FF8000 , filesize: 90368 bytes
4/16/2018 12:31:17 PM> eMMC switching to ROM1
4/16/2018 12:31:17 PM> Erasing partition...
4/16/2018 12:31:18 PM> Writing partition...
4/16/2018 12:31:18 PM> Done writing partition. Write speed: 978.70 KB/s
4/16/2018 12:31:18 PM> Partition name: SEC
4/16/2018 12:31:18 PM> Filename: sec.dat , Offset: 000005378000 , filesize: 684 bytes
4/16/2018 12:31:18 PM> eMMC switching to ROM1
4/16/2018 12:31:18 PM> Erasing partition...
4/16/2018 12:31:19 PM> Writing partition...
4/16/2018 12:31:19 PM> Done writing partition. Write speed: 12.46 KB/s
4/16/2018 12:31:19 PM> Partition name: BOOT
4/16/2018 12:31:19 PM> Filename: boot.img , Offset: 000007C00000 , filesize: 10273040 bytes
4/16/2018 12:31:19 PM> eMMC switching to ROM1
4/16/2018 12:31:19 PM> Erasing partition...
4/16/2018 12:31:20 PM> Writing partition...
4/16/2018 12:31:24 PM> Done writing partition. Write speed: 2559.07 KB/s
4/16/2018 12:31:24 PM> Partition name: RECOVERY
4/16/2018 12:31:24 PM> Filename: recovery.img , Offset: 000008900000 , filesize: 10955024 bytes
4/16/2018 12:31:24 PM> eMMC switching to ROM1
4/16/2018 12:31:24 PM> Erasing partition...
4/16/2018 12:31:25 PM> Writing partition...
4/16/2018 12:31:29 PM> Done writing partition. Write speed: 2510.03 KB/s
4/16/2018 12:31:29 PM> Partition name: PERSIST
4/16/2018 12:31:29 PM> Filename: persist.img.ext4 , Offset: 00000A700000 , filesize: 4350076 bytes
4/16/2018 12:31:29 PM> eMMC switching to ROM1
4/16/2018 12:31:29 PM> Erasing partition...
4/16/2018 12:31:30 PM> Writing partition...
4/16/2018 12:31:30 PM> Sparse image found v.1.0 Total chunks: 8
4/16/2018 12:31:32 PM> Done writing partition. Write speed: 2264.76 KB/s
4/16/2018 12:31:32 PM> Partition name: SYSTEM
4/16/2018 12:31:32 PM> Filename: system.img.ext4 , Offset: 00000B800000 , filesize: 1320231292 bytes
4/16/2018 12:31:32 PM> eMMC switching to ROM1
4/16/2018 12:31:32 PM> Erasing partition...
4/16/2018 12:32:11 PM> Writing partition...
4/16/2018 12:32:11 PM> Sparse image found v.1.0 Total chunks: 2760
4/16/2018 12:41:34 PM> Done writing partition. Write speed: 2291.29 KB/s
4/16/2018 12:41:34 PM> Partition name: CACHE
4/16/2018 12:41:34 PM> Filename: cache.img.ext4 , Offset: 000069400000 , filesize: 7438556 bytes
4/16/2018 12:41:34 PM> eMMC switching to ROM1
4/16/2018 12:41:34 PM> Erasing partition...
4/16/2018 12:41:40 PM> Writing partition...
4/16/2018 12:41:40 PM> Sparse image found v.1.0 Total chunks: 16
4/16/2018 12:41:43 PM> Done writing partition. Write speed: 2328.35 KB/s
4/16/2018 12:41:43 PM> Partition name: HIDDEN
4/16/2018 12:41:43 PM> Filename: hidden.img.ext4 , Offset: 000075C00000 , filesize: 30044560 bytes
4/16/2018 12:41:43 PM> eMMC switching to ROM1
4/16/2018 12:41:43 PM> Erasing partition...
4/16/2018 12:41:44 PM> Writing partition...
4/16/2018 12:41:44 PM> Sparse image found v.1.0 Total chunks: 31
4/16/2018 12:41:56 PM> Done writing partition. Write speed: 2419.96 KB/s
4/16/2018 12:41:56 PM>
4/16/2018 12:41:58 PM> Critical error: Access violation at address 00E1387E in module 'eMMC_tool.exe'. Read of address 00000004.


G360F onluy qcomm driver, need help