GSM-Forum - View Single Post - Successfully unlocked/repaired phones by Infinity-Box

azhergoga007 · 10-02-2018, 13:19

Operation : Format FileSystem [ v1.03 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device not found!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect Power/Cable!

Operation : Format FileSystem [ v1.03 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
ERROR : Protocol HandShake failed!

Error : Fail to init protocol!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect Power/Cable!

Operation : Format FileSystem [ v1.03 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device not found!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect Power/Cable!

Operation : Format FileSystem [ v1.03 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
BootSource : InternalLibrary
ERROR : FDL NOT started!

Error : Loader send failed!
Wrong model selected! Select correct one!

Reconnect Power/Cable!

SPRD mode : SC6531 : REV : C000 : NOR

Operation : Format FileSystem [ v1.03 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
ERROR : Protocol HandShake failed!

Error : Fail to init protocol!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect Power/Cable!

Operation : Format FileSystem [ v1.03 ]

1. Power off device
2. Press and hold BootKey or use BootCable
3. Insert cable and battery in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
BootSource : InternalLibrary
BootVersion : Spreadtrum Boot Block version 1.2
Port speed : 921600
FDL Flash : Control transfered!

Boot Done!

CS0_MEM : SPI : [WINBOND] : W25Q32 : 0x00400000 [ 4MiB ]

Make backup of sensetive data
Backup saved to : C:\InfinityBox\CM2SCR\Backup\00400000_FMT_BACK_009 554ADAB0C_NVM.nv

Executing FormatFFS ...
Format FFS Done!

Done!
Elapsed: 00:00:18

Reconnect Power/Cable!

10-02-2018, 13:19	#53680 (permalink)
azhergoga007 No Life Poster Join Date: Jan 2011 Location: lullipapi Posts: 8,670 Member: 1489030 Status: Offline Sonork: 100.1649409 Thanks Meter: 5,368	Mango Kig 2SCR SPD Logo Stuck Fix Only Formate With Infinity CM2 Operation : Format FileSystem [ v1.03 ] 1. Power off device 2. Press and hold BootKey or use BootCable 3. Insert cable and battery in device! Wait for device ... Device not found! Remove battery, cable. Check cable and connection. Repeat operation! Reconnect Power/Cable! Operation : Format FileSystem [ v1.03 ] 1. Power off device 2. Press and hold BootKey or use BootCable 3. Insert cable and battery in device! Wait for device ... Device Connected! ERROR : Protocol HandShake failed! Error : Fail to init protocol! Remove battery, cable. Check cable and connection. Repeat operation! Reconnect Power/Cable! Operation : Format FileSystem [ v1.03 ] 1. Power off device 2. Press and hold BootKey or use BootCable 3. Insert cable and battery in device! Wait for device ... Device not found! Remove battery, cable. Check cable and connection. Repeat operation! Reconnect Power/Cable! Operation : Format FileSystem [ v1.03 ] 1. Power off device 2. Press and hold BootKey or use BootCable 3. Insert cable and battery in device! Wait for device ... Device Connected! BootVersion : SPRD3 BootSource : InternalLibrary ERROR : FDL NOT started! Error : Loader send failed! Wrong model selected! Select correct one! Reconnect Power/Cable! SPRD mode : SC6531 : REV : C000 : NOR Operation : Format FileSystem [ v1.03 ] 1. Power off device 2. Press and hold BootKey or use BootCable 3. Insert cable and battery in device! Wait for device ... Device Connected! ERROR : Protocol HandShake failed! Error : Fail to init protocol! Remove battery, cable. Check cable and connection. Repeat operation! Reconnect Power/Cable! Operation : Format FileSystem [ v1.03 ] 1. Power off device 2. Press and hold BootKey or use BootCable 3. Insert cable and battery in device! Wait for device ... Device Connected! BootVersion : SPRD3 BootSource : InternalLibrary BootVersion : Spreadtrum Boot Block version 1.2 Port speed : 921600 FDL Flash : Control transfered! Boot Done! CS0_MEM : SPI : [WINBOND] : W25Q32 : 0x00400000 [ 4MiB ] Make backup of sensetive data Backup saved to : C:\InfinityBox\CM2SCR\Backup\00400000_FMT_BACK_009 554ADAB0C_NVM.nv Executing FormatFFS ... Format FFS Done! Done! Elapsed: 00:00:18 Reconnect Power/Cable!