[mrmmethun555]

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 18 Mhz
CMD Pullup Level: 1804 mV
CMD Active Level: 1867 mV
EMMC Device Information :
EMMC CID: 90014A48344732621101C13351BD3271
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: C13351BD , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 3/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_C13351BD_20190415_184607.extcsd
EMMC Init completed.

Opening file: j13g_HIDDEN_140M.pit

Pit: j13g_HIDDEN_140M.pit
Entry count: 29

The size of the last section has been updated

J100HXXU0AOAB_J100HOLB0AOA3_J100HDXU0AOA1_HOME.tar .md5
The list of files in the firmware:
boot.img
recovery.img
system.img
sprdcp.img
sprddsp.img
nvitem.bin
cache.img
hidden.img

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 18 Mhz
CMD Pullup Level: 1806 mV
CMD Active Level: 1866 mV
EMMC Device Information :
EMMC CID: 90014A48344732621101C13351BD3271
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: C13351BD , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 3/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_C13351BD_20190415_184623.extcsd
EMMC Init completed.

Operation: Write by vendor (Samsung)

Creating GPT-partitioninig
Writing PrimaryGPT at address: 000000000000
Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #1
Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #2
Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #3
Too many errors. Writing has been stopped