GSM-Forum - View Single Post - Galaxy J2 Prime G532G Dead Boot Repair Full Guide

apologized · 07-27-2019, 02:18

same problem even with this firmware (G532GDXU1AQK1_ZZT1AQK1) or this comb (COMBINATION_OXE_FA60_G532GDXU1AQJ1) any idea ?

Quote:

26/07/2019 16:53:12>
26/07/2019 16:53:12> eMMC_tool Suite ver. 1.6.2.0 (release date: 30.06.2019)
26/07/2019 16:53:15> Microsoft Windows 7 (32 bit) build 7601 (6.1.7601.18015)
26/07/2019 16:53:15>
26/07/2019 16:53:15> Looking for EasyJTAG box...
26/07/2019 16:53:15> EasyJTAG API ver. 3307
26/07/2019 16:53:17> OpenUSB returned = 0
26/07/2019 16:53:19> EasyJTAG Box Serial = 14140E12A2C07F42
26/07/2019 16:53:20> Card Serial = AA95BECE
26/07/2019 16:53:20> EasyJTAG Box Firmware = 1.63
26/07/2019 16:53:20>
26/07/2019 16:53:32> Looking for EasyJTAG box...
26/07/2019 16:53:32> EasyJTAG API ver. 3307
26/07/2019 16:53:32> Setting IO Levels to 1.8V
26/07/2019 16:53:32> Setting frequence to 21 MHz
26/07/2019 16:53:33> EasyJTAG Box Serial = 14140E12A2C07F42
26/07/2019 16:53:33> EasyJTAG Box Firmware = 1.63
26/07/2019 16:53:36> Setting frequence to 21 MHz
26/07/2019 16:53:36> CMD Pullup Level: 1794 mV
26/07/2019 16:53:36> CMD Active Level: 2083 mV
26/07/2019 16:53:36> eMMC Init returned = 0
26/07/2019 16:53:36> EMMC Device Information :
26/07/2019 16:53:36> EMMC CID: 90014A483847347592011E67A139156E
26/07/2019 16:53:36> EMMC CSD: D02701320F5903FFFFFFFFE78A40002A
26/07/2019 16:53:36> EMMC Manufacture : SKHYNIX , EMMC NAME: H8G4u , HEX: 483847347500 , S/N: 1E67A139 , rev. 0x01
26/07/2019 16:53:36> EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 1/2018
26/07/2019 16:53:36> EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)
26/07/2019 16:53:36> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
26/07/2019 16:53:36> EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 0 , Response: Maybe not clean
26/07/2019 16:53:37> EMMC Permanent Write Protection: No
26/07/2019 16:53:37> EMMC Temporary Write Protection: No
26/07/2019 16:53:37> Extended CSD Information :
26/07/2019 16:53:37> Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)
26/07/2019 16:53:37> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
26/07/2019 16:53:37> Boot Bus Config: 0x00 , width 1bit
26/07/2019 16:53:37> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
26/07/2019 16:53:37> Supported partition features [PARTITIONING_SUPPORT]: 0x07
26/07/2019 16:53:37> Device supports partitioning features
26/07/2019 16:53:37> Device can have enhanced technological features in partitions and user data area
26/07/2019 16:53:37> Device can have extended partitions attribute
26/07/2019 16:53:37> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
26/07/2019 16:53:37> Backup saved: H8G4u_1E67A139_20190726_165337.extcsd
26/07/2019 16:53:37> EMMC Init completed.
26/07/2019 16:53:37>
26/07/2019 16:53:54> Looking for EasyJTAG box...
26/07/2019 16:53:54> EasyJTAG API ver. 3307
26/07/2019 16:53:54> Setting IO Levels to 1.8V
26/07/2019 16:53:54> Setting frequence to 21 MHz
26/07/2019 16:53:56> EasyJTAG Box Serial = 14140E12A2C07F42
26/07/2019 16:53:56> EasyJTAG Box Firmware = 1.63
26/07/2019 16:53:58> Setting frequence to 21 MHz
26/07/2019 16:53:58>
26/07/2019 16:53:58> Error: First select the Pit-file
26/07/2019 16:53:58>
26/07/2019 16:53:58> CMD Pullup Level: 1794 mV
26/07/2019 16:53:58> CMD Active Level: 2083 mV
26/07/2019 16:53:59> eMMC Init returned = 0
26/07/2019 16:53:59> EMMC Device Information :
26/07/2019 16:53:59> EMMC CID: 90014A483847347592011E67A139156E
26/07/2019 16:53:59> EMMC CSD: D02701320F5903FFFFFFFFE78A40002A
26/07/2019 16:53:59> EMMC Manufacture : SKHYNIX , EMMC NAME: H8G4u , HEX: 483847347500 , S/N: 1E67A139 , rev. 0x01
26/07/2019 16:53:59> EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 1/2018
26/07/2019 16:53:59> EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)
26/07/2019 16:53:59> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
26/07/2019 16:53:59> EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 0 , Response: Maybe not clean
26/07/2019 16:53:59> EMMC Permanent Write Protection: No
26/07/2019 16:53:59> EMMC Temporary Write Protection: No
26/07/2019 16:53:59> Extended CSD Information :
26/07/2019 16:53:59> Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)
26/07/2019 16:53:59> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
26/07/2019 16:53:59> Boot Bus Config: 0x00 , width 1bit
26/07/2019 16:53:59> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
26/07/2019 16:53:59> Supported partition features [PARTITIONING_SUPPORT]: 0x07
26/07/2019 16:53:59> Device supports partitioning features
26/07/2019 16:53:59> Device can have enhanced technological features in partitions and user data area
26/07/2019 16:53:59> Device can have extended partitions attribute
26/07/2019 16:53:59> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
26/07/2019 16:53:59> Backup saved: H8G4u_1E67A139_20190726_165359.extcsd
26/07/2019 16:53:59> EMMC Init completed.
26/07/2019 16:53:59>
26/07/2019 16:53:59> Opening file: C:\Users\OP\Desktop\G532GDXU1AQK1_ZZT1AQK1\GRANDPP LTE_CIS_SER_HIDDEN100M.pit
26/07/2019 16:53:59>
26/07/2019 16:53:59> Pit: GRANDPPLTE_CIS_SER_HIDDEN100M.pit
26/07/2019 16:53:59> Entry count: 34
26/07/2019 16:53:59>
26/07/2019 16:53:59> The size of the last section has been updated
26/07/2019 16:54:09> Selected file: C:\Users\OP\Desktop\G532GDXU1AQK1_ZZT1AQK1\BL_G532 GDXU1AQK1_CL12551713_QB15688219_REV00_user_low_shi p_MULTI_CERT.tar.md5
26/07/2019 16:54:09>
26/07/2019 16:54:09> BL_G532GDXU1AQK1_CL12551713_QB15688219_REV00_user_ low_ship_MULTI_CERT.tar.md5
26/07/2019 16:54:09> The list of files in the firmware:
26/07/2019 16:54:09> preloader.img
26/07/2019 16:54:09> lk.bin
26/07/2019 16:54:09> param.bin
26/07/2019 16:54:09> trustzone.bin
26/07/2019 16:54:09> efuse.img
26/07/2019 16:54:09>
26/07/2019 16:54:12> Looking for EasyJTAG box...
26/07/2019 16:54:12> EasyJTAG API ver. 3307
26/07/2019 16:54:12> Setting IO Levels to 1.8V
26/07/2019 16:54:12> Setting frequence to 21 MHz
26/07/2019 16:54:13> EasyJTAG Box Serial = 14140E12A2C07F42
26/07/2019 16:54:13> EasyJTAG Box Firmware = 1.63
26/07/2019 16:54:16> Setting frequence to 21 MHz
26/07/2019 16:54:16> CMD Pullup Level: 1784 mV
26/07/2019 16:54:16> CMD Active Level: 2072 mV
26/07/2019 16:54:16> eMMC Init returned = 0
26/07/2019 16:54:16> EMMC Device Information :
26/07/2019 16:54:16> EMMC CID: 90014A483847347592011E67A139156E
26/07/2019 16:54:16> EMMC CSD: D02701320F5903FFFFFFFFE78A40002A
26/07/2019 16:54:16> EMMC Manufacture : SKHYNIX , EMMC NAME: H8G4u , HEX: 483847347500 , S/N: 1E67A139 , rev. 0x01
26/07/2019 16:54:16> EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 1/2018
26/07/2019 16:54:16> EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)
26/07/2019 16:54:16> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
26/07/2019 16:54:17> EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 0 , Response: Maybe not clean
26/07/2019 16:54:17> EMMC Permanent Write Protection: No
26/07/2019 16:54:17> EMMC Temporary Write Protection: No
26/07/2019 16:54:17> Extended CSD Information :
26/07/2019 16:54:17> Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)
26/07/2019 16:54:17> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
26/07/2019 16:54:17> Boot Bus Config: 0x00 , width 1bit
26/07/2019 16:54:17> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
26/07/2019 16:54:17> Supported partition features [PARTITIONING_SUPPORT]: 0x07
26/07/2019 16:54:17> Device supports partitioning features
26/07/2019 16:54:17> Device can have enhanced technological features in partitions and user data area
26/07/2019 16:54:17> Device can have extended partitions attribute
26/07/2019 16:54:17> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
26/07/2019 16:54:17> Backup saved: H8G4u_1E67A139_20190726_165417.extcsd
26/07/2019 16:54:17> EMMC Init completed.
26/07/2019 16:54:17>
26/07/2019 16:54:17> Operation: Write by vendor (Samsung)
26/07/2019 16:54:17>
26/07/2019 16:54:17> Creating GPT-partitioninig
26/07/2019 16:54:17> Writing PrimaryGPT at address: 000000000000
26/07/2019 16:54:17> Writing BackupGPT at address: 0001D1FFBE00
26/07/2019 16:54:17> Writing PIT at address: 000000004400
26/07/2019 16:54:17> GPT-partitioning done
26/07/2019 16:54:17>
26/07/2019 16:54:17> Unpacking file: preloader.img
26/07/2019 16:54:17> Unpacking file: lk.bin
26/07/2019 16:54:17> Unpacking file: efuse.img
26/07/2019 16:54:17> Unpacking file: trustzone.bin
26/07/2019 16:54:17> Unpacking file: param.bin
26/07/2019 16:54:17>
26/07/2019 16:54:17> Partition name: BOOTLOADER
26/07/2019 16:54:17> Filename: preloader.img , Offset: 000000000000 , filesize: 170240 bytes
26/07/2019 16:54:17> eMMC switching to ROM2
26/07/2019 16:54:18> Erasing partition...
26/07/2019 16:54:39> Writing partition...
26/07/2019 16:54:40> Done writing partition. Write speed: 163,43 KB/s
26/07/2019 16:54:40> Partition name: LK
26/07/2019 16:54:40> Filename: lk.bin , Offset: 000001000000 , filesize: 590336 bytes
26/07/2019 16:54:40> eMMC switching to ROM1
26/07/2019 16:54:40> Erasing partition...
26/07/2019 16:54:43> Writing partition...
26/07/2019 16:54:45> Done writing partition. Write speed: 299,86 KB/s
26/07/2019 16:54:45> Partition name: EFUSE
26/07/2019 16:54:45> Filename: efuse.img , Offset: 000001B80000 , filesize: 768 bytes
26/07/2019 16:54:45> eMMC switching to ROM1
26/07/2019 16:54:45> Erasing partition...
26/07/2019 16:54:46> Writing partition...
26/07/2019 16:54:46> Done writing partition. Write speed: 7,86 KB/s
26/07/2019 16:54:46> Partition name: TEE1
26/07/2019 16:54:46> Filename: trustzone.bin , Offset: 000001C00000 , filesize: 324352 bytes
26/07/2019 16:54:46> eMMC switching to ROM1
26/07/2019 16:54:46> Erasing partition...
26/07/2019 16:54:47> Writing partition...
26/07/2019 16:54:48> Done writing partition. Write speed: 464,49 KB/s
26/07/2019 16:54:48> Partition name: PARAM
26/07/2019 16:54:48> Filename: param.bin , Offset: 000005000000 , filesize: 747520 bytes
26/07/2019 16:54:48> eMMC switching to ROM1
26/07/2019 16:54:48> Erasing partition...
26/07/2019 16:54:50> Writing partition...
26/07/2019 16:54:51> Done writing partition. Write speed: 573,94 KB/s
26/07/2019 16:54:52>
26/07/2019 16:54:55> Partition USERDATA : formatting as EXT4. Please wait ...
26/07/2019 16:55:08> Formatting completed
26/07/2019 16:55:08>
26/07/2019 16:55:08> Check BootConfig for the selected vendor
26/07/2019 16:55:08>
26/07/2019 16:55:08> All done time: [00:00:50:645]
26/07/2019 16:55:08>
26/07/2019 16:56:59> Looking for EasyJTAG box...
26/07/2019 16:56:59> EasyJTAG API ver. 3307
26/07/2019 16:56:59> Setting IO Levels to 1.8V
26/07/2019 16:56:59> Setting frequence to 21 MHz
26/07/2019 16:57:00> EasyJTAG Box Serial = 14140E12A2C07F42
26/07/2019 16:57:00> EasyJTAG Box Firmware = 1.63
26/07/2019 16:57:03> Setting frequence to 21 MHz
26/07/2019 16:57:03> CMD Pullup Level: 1794 mV
26/07/2019 16:57:03> CMD Active Level: 2072 mV
26/07/2019 16:57:03> eMMC Init returned = 0
26/07/2019 16:57:03> EMMC Device Information :
26/07/2019 16:57:03> EMMC CID: 90014A483847347592011E67A139156E
26/07/2019 16:57:03> EMMC CSD: D02701320F5903FFFFFFFFE78A40002A
26/07/2019 16:57:03> EMMC Manufacture : SKHYNIX , EMMC NAME: H8G4u , HEX: 483847347500 , S/N: 1E67A139 , rev. 0x01
26/07/2019 16:57:03> EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 1/2018
26/07/2019 16:57:03> EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)
26/07/2019 16:57:03> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
26/07/2019 16:57:03> EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 0 , Response: Maybe not clean
26/07/2019 16:57:03> EMMC Permanent Write Protection: No
26/07/2019 16:57:03> EMMC Temporary Write Protection: No
26/07/2019 16:57:04> Extended CSD Information :
26/07/2019 16:57:04> Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)
26/07/2019 16:57:04> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
26/07/2019 16:57:04> Boot Bus Config: 0x00 , width 1bit
26/07/2019 16:57:04> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
26/07/2019 16:57:04> Supported partition features [PARTITIONING_SUPPORT]: 0x07
26/07/2019 16:57:04> Device supports partitioning features
26/07/2019 16:57:04> Device can have enhanced technological features in partitions and user data area
26/07/2019 16:57:04> Device can have extended partitions attribute
26/07/2019 16:57:04> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
26/07/2019 16:57:04> Backup saved: H8G4u_1E67A139_20190726_165704.extcsd
26/07/2019 16:57:04> EMMC Init completed.
26/07/2019 16:57:04>
26/07/2019 16:57:08> Looking for EasyJTAG box...
26/07/2019 16:57:08> EasyJTAG API ver. 3307
26/07/2019 16:57:08> Setting IO Levels to 1.8V
26/07/2019 16:57:08> Setting frequence to 21 MHz
26/07/2019 16:57:10> EasyJTAG Box Serial = 14140E12A2C07F42
26/07/2019 16:57:10> EasyJTAG Box Firmware = 1.63
26/07/2019 16:57:12> Setting frequence to 21 MHz
26/07/2019 16:57:12> CMD Pullup Level: 1794 mV
26/07/2019 16:57:12> CMD Active Level: 2072 mV
26/07/2019 16:57:13> eMMC Init returned = 0
26/07/2019 16:57:13> EMMC Device Information :
26/07/2019 16:57:13> EMMC CID: 90014A483847347592011E67A139156E
26/07/2019 16:57:13> EMMC CSD: D02701320F5903FFFFFFFFE78A40002A
26/07/2019 16:57:13> EMMC Manufacture : SKHYNIX , EMMC NAME: H8G4u , HEX: 483847347500 , S/N: 1E67A139 , rev. 0x01
26/07/2019 16:57:13> EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 1/2018
26/07/2019 16:57:13> EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)
26/07/2019 16:57:13> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
26/07/2019 16:57:13> EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 0 , Response: Maybe not clean
26/07/2019 16:57:13> EMMC Permanent Write Protection: No
26/07/2019 16:57:13> EMMC Temporary Write Protection: No
26/07/2019 16:57:13> Extended CSD Information :
26/07/2019 16:57:13> Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)
26/07/2019 16:57:13> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
26/07/2019 16:57:13> Boot Bus Config: 0x00 , width 1bit
26/07/2019 16:57:13> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
26/07/2019 16:57:13> Supported partition features [PARTITIONING_SUPPORT]: 0x07
26/07/2019 16:57:13> Device supports partitioning features
26/07/2019 16:57:13> Device can have enhanced technological features in partitions and user data area
26/07/2019 16:57:13> Device can have extended partitions attribute
26/07/2019 16:57:13> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
26/07/2019 16:57:13> Backup saved: H8G4u_1E67A139_20190726_165713.extcsd
26/07/2019 16:57:13> EMMC Init completed.
26/07/2019 16:57:13>
26/07/2019 16:57:13> Get firmware version
26/07/2019 16:57:13>
26/07/2019 16:57:22> Brand = samsung
26/07/2019 16:57:22> Manufacturer = samsung
26/07/2019 16:57:22> Device = grandpplte
26/07/2019 16:57:22> Model = SM-G532G
26/07/2019 16:57:22> Phone platform = mt6737t
26/07/2019 16:57:22> CPU Abi = armeabi-v7a
26/07/2019 16:57:22> Mediatek platform = MT6737T
26/07/2019 16:57:22> Android release = 6.0.1
26/07/2019 16:57:22> Firmware version = MMB29T.G532GDXU1AQA4
26/07/2019 16:57:22> Firmware date = Mon Jan 23 20:44:01 KST 2017
26/07/2019 16:58:10> Selected file: C:\Users\OP\Desktop\COMBINATION_OXE_FA60_G532GDXU1 AQJ1_OXEFA60_G532GOLB1AQJ1_CL11108991_QB15342015_R EV00_user_mid_noship_MULTI_CERT.tar.md5
26/07/2019 16:58:10>
26/07/2019 16:58:10> COMBINATION_OXE_FA60_G532GDXU1AQJ1_OXEFA60_G532GOL B1AQJ1_CL11108991_QB15342015_REV00_user_mid_noship _MULTI_CERT.tar.md5
26/07/2019 16:58:10> The list of files in the firmware:
26/07/2019 16:58:10> preloader.img
26/07/2019 16:58:10> lk.bin
26/07/2019 16:58:10> param.bin
26/07/2019 16:58:10> trustzone.bin
26/07/2019 16:58:10> efuse.img
26/07/2019 16:58:10> boot.img
26/07/2019 16:58:10> recovery.img
26/07/2019 16:58:10> system.img
26/07/2019 16:58:10> secro.img
26/07/2019 16:58:10> md1rom.img
26/07/2019 16:58:10> md1dsp.img
26/07/2019 16:58:10> grandpplte_cis_ser.pit
26/07/2019 16:58:10> cache.img
26/07/2019 16:58:10>
26/07/2019 16:58:17> Looking for EasyJTAG box...
26/07/2019 16:58:17> EasyJTAG API ver. 3307
26/07/2019 16:58:17> Setting IO Levels to 1.8V
26/07/2019 16:58:17> Setting frequence to 21 MHz
26/07/2019 16:58:18> EasyJTAG Box Serial = 14140E12A2C07F42
26/07/2019 16:58:18> EasyJTAG Box Firmware = 1.63
26/07/2019 16:58:21> Setting frequence to 21 MHz
26/07/2019 16:58:21> CMD Pullup Level: 1784 mV
26/07/2019 16:58:21> CMD Active Level: 2072 mV
26/07/2019 16:58:21> eMMC Init returned = 0
26/07/2019 16:58:21> EMMC Device Information :
26/07/2019 16:58:21> EMMC CID: 90014A483847347592011E67A139156E
26/07/2019 16:58:21> EMMC CSD: D02701320F5903FFFFFFFFE78A40002A
26/07/2019 16:58:21> EMMC Manufacture : SKHYNIX , EMMC NAME: H8G4u , HEX: 483847347500 , S/N: 1E67A139 , rev. 0x01
26/07/2019 16:58:21> EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 1/2018
26/07/2019 16:58:21> EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)
26/07/2019 16:58:21> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
26/07/2019 16:58:21> EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 0 , Response: Maybe not clean
26/07/2019 16:58:21> EMMC Permanent Write Protection: No
26/07/2019 16:58:21> EMMC Temporary Write Protection: No
26/07/2019 16:58:21> Extended CSD Information :
26/07/2019 16:58:21> Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)
26/07/2019 16:58:21> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
26/07/2019 16:58:22> Boot Bus Config: 0x00 , width 1bit
26/07/2019 16:58:22> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
26/07/2019 16:58:22> Supported partition features [PARTITIONING_SUPPORT]: 0x07
26/07/2019 16:58:22> Device supports partitioning features
26/07/2019 16:58:22> Device can have enhanced technological features in partitions and user data area
26/07/2019 16:58:22> Device can have extended partitions attribute
26/07/2019 16:58:22> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
26/07/2019 16:58:22> Backup saved: H8G4u_1E67A139_20190726_165822.extcsd
26/07/2019 16:58:22> EMMC Init completed.
26/07/2019 16:58:22>
26/07/2019 16:58:22> Operation: Write by vendor (Samsung)
26/07/2019 16:58:22>
26/07/2019 16:58:22> Creating GPT-partitioninig
26/07/2019 16:58:22> Writing PrimaryGPT at address: 000000000000
26/07/2019 16:58:22> Writing BackupGPT at address: 0001D1FFBE00
26/07/2019 16:58:22> Writing PIT at address: 000000004400
26/07/2019 16:58:22> GPT-partitioning done
26/07/2019 16:58:22>
26/07/2019 16:58:22> Unpacking file: preloader.img
26/07/2019 16:58:22> Unpacking file: lk.bin
26/07/2019 16:58:22> Unpacking file: secro.img
26/07/2019 16:58:22> Unpacking file: efuse.img
26/07/2019 16:58:22> Unpacking file: trustzone.bin
26/07/2019 16:58:22> Unpacking file: param.bin
26/07/2019 16:58:22> Unpacking file: recovery.img
26/07/2019 16:58:22> Unpacking file: boot.img
26/07/2019 16:58:22> Unpacking file: md1rom.img
26/07/2019 16:58:22> Unpacking file: md1dsp.img
26/07/2019 16:58:22> Unpacking file: system.img
26/07/2019 16:58:35> Unpacking file: cache.img
26/07/2019 16:58:35>
26/07/2019 16:58:35> Partition name: BOOTLOADER
26/07/2019 16:58:35> Filename: preloader.img , Offset: 000000000000 , filesize: 170240 bytes
26/07/2019 16:58:35> eMMC switching to ROM2
26/07/2019 16:58:35> Erasing partition...
26/07/2019 16:58:56> Writing partition...
26/07/2019 16:58:57> Done writing partition. Write speed: 163,27 KB/s
26/07/2019 16:58:57> Partition name: LK
26/07/2019 16:58:57> Filename: lk.bin , Offset: 000001000000 , filesize: 590336 bytes
26/07/2019 16:58:57> eMMC switching to ROM1
26/07/2019 16:58:57> Erasing partition...
26/07/2019 16:59:00> Writing partition...
26/07/2019 16:59:02> Done writing partition. Write speed: 308,15 KB/s
26/07/2019 16:59:02> Partition name: SECRO
26/07/2019 16:59:02> Filename: secro.img , Offset: 000001400000 , filesize: 135424 bytes
26/07/2019 16:59:02> eMMC switching to ROM1
26/07/2019 16:59:03> Erasing partition...
26/07/2019 16:59:04> Writing partition...
26/07/2019 16:59:04> Done writing partition. Write speed: 499,00 KB/s
26/07/2019 16:59:04> Partition name: EFUSE
26/07/2019 16:59:04> Filename: efuse.img , Offset: 000001B80000 , filesize: 768 bytes
26/07/2019 16:59:04> eMMC switching to ROM1
26/07/2019 16:59:05> Erasing partition...
26/07/2019 16:59:05> Writing partition...
26/07/2019 16:59:05> Done writing partition. Write speed: 13,17 KB/s
26/07/2019 16:59:05> Partition name: TEE1
26/07/2019 16:59:05> Filename: trustzone.bin , Offset: 000001C00000 , filesize: 324352 bytes
26/07/2019 16:59:05> eMMC switching to ROM1
26/07/2019 16:59:06> Erasing partition...
26/07/2019 16:59:07> Writing partition...
26/07/2019 16:59:08> Done writing partition. Write speed: 522,38 KB/s
26/07/2019 16:59:08> Partition name: PARAM
26/07/2019 16:59:08> Filename: param.bin , Offset: 000005000000 , filesize: 747520 bytes
26/07/2019 16:59:08> eMMC switching to ROM1
26/07/2019 16:59:08> Erasing partition...
26/07/2019 16:59:10> Writing partition...
26/07/2019 16:59:11> Done writing partition. Write speed: 587,25 KB/s
26/07/2019 16:59:11> Partition name: RECOVERY
26/07/2019 16:59:11> Filename: recovery.img , Offset: 000005800000 , filesize: 10699024 bytes
26/07/2019 16:59:11> eMMC switching to ROM1
26/07/2019 16:59:11> Erasing partition...
26/07/2019 16:59:14> Writing partition...
26/07/2019 16:59:32> Done writing partition. Write speed: 589,37 KB/s
26/07/2019 16:59:32> Partition name: BOOT
26/07/2019 16:59:32> Filename: boot.img , Offset: 000006800000 , filesize: 9548048 bytes
26/07/2019 16:59:32> eMMC switching to ROM1
26/07/2019 16:59:32> Erasing partition...
26/07/2019 16:59:35> Writing partition...
26/07/2019 16:59:51> Done writing partition. Write speed: 586,63 KB/s
26/07/2019 16:59:51> Partition name: MD1IMG
26/07/2019 16:59:51> Filename: md1rom.img , Offset: 000007800000 , filesize: 10506752 bytes
26/07/2019 16:59:51> eMMC switching to ROM1
26/07/2019 16:59:51> Erasing partition...
26/07/2019 16:59:56> Writing partition...
26/07/2019 17:00:13> Done writing partition. Write speed: 589,23 KB/s
26/07/2019 17:00:13> Partition name: MD1DSP
26/07/2019 17:00:13> Filename: md1dsp.img , Offset: 000009800000 , filesize: 1417728 bytes
26/07/2019 17:00:13> eMMC switching to ROM1
26/07/2019 17:00:14> Erasing partition...
26/07/2019 17:00:15> Writing partition...
26/07/2019 17:00:17> Done writing partition. Write speed: 587,80 KB/s
26/07/2019 17:00:17> Partition name: SYSTEM
26/07/2019 17:00:17> Filename: system.img , Offset: 00000C000000 , filesize: 1088833088 bytes
26/07/2019 17:00:17> eMMC switching to ROM1
26/07/2019 17:00:18> Erasing partition...
26/07/2019 17:07:39> Writing partition...
26/07/2019 17:07:39> Sparse image found v.1.0 Total chunks: 2402
26/07/2019 17:38:52> Done writing partition. Write speed: 567,61 KB/s
26/07/2019 17:38:53> Partition name: CACHE
26/07/2019 17:38:53> Filename: cache.img , Offset: 0000CC800000 , filesize: 8266096 bytes
26/07/2019 17:38:53> eMMC switching to ROM1
26/07/2019 17:38:53> Erasing partition...
26/07/2019 17:39:50> Writing partition...
26/07/2019 17:39:50> Sparse image found v.1.0 Total chunks: 21
26/07/2019 17:40:05> Done writing partition. Write speed: 568,89 KB/s
26/07/2019 17:40:05>
26/07/2019 17:40:05> Check BootConfig for the selected vendor
26/07/2019 17:40:05>
26/07/2019 17:40:06> All done time: [00:41:30:805]
26/07/2019 17:40:06>
26/07/2019 17:40:55> Looking for EasyJTAG box...
26/07/2019 17:40:55> EasyJTAG API ver. 3307
26/07/2019 17:40:55> Setting IO Levels to 1.8V
26/07/2019 17:40:55> Setting frequence to 21 MHz
26/07/2019 17:40:56> EasyJTAG Box Serial = 14140E12A2C07F42
26/07/2019 17:40:56> EasyJTAG Box Firmware = 1.63
26/07/2019 17:40:59> Setting frequence to 21 MHz
26/07/2019 17:40:59> CMD Pullup Level: 1794 mV
26/07/2019 17:40:59> CMD Active Level: 2072 mV
26/07/2019 17:40:59> eMMC Init returned = 0
26/07/2019 17:40:59> EMMC Device Information :
26/07/2019 17:40:59> EMMC CID: 90014A483847347592011E67A139156E
26/07/2019 17:40:59> EMMC CSD: D02701320F5903FFFFFFFFE78A40002A
26/07/2019 17:40:59> EMMC Manufacture : SKHYNIX , EMMC NAME: H8G4u , HEX: 483847347500 , S/N: 1E67A139 , rev. 0x01
26/07/2019 17:40:59> EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 1/2018
26/07/2019 17:40:59> EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)
26/07/2019 17:40:59> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
26/07/2019 17:40:59> EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 0 , Response: Maybe not clean
26/07/2019 17:40:59> EMMC Permanent Write Protection: No
26/07/2019 17:40:59> EMMC Temporary Write Protection: No
26/07/2019 17:40:59> Extended CSD Information :
26/07/2019 17:40:59> Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)
26/07/2019 17:40:59> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
26/07/2019 17:40:59> Boot Bus Config: 0x00 , width 1bit
26/07/2019 17:40:59> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
26/07/2019 17:40:59> Supported partition features [PARTITIONING_SUPPORT]: 0x07
26/07/2019 17:40:59> Device supports partitioning features
26/07/2019 17:40:59> Device can have enhanced technological features in partitions and user data area
26/07/2019 17:40:59> Device can have extended partitions attribute
26/07/2019 17:41:00> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
26/07/2019 17:41:00> Backup saved: H8G4u_1E67A139_20190726_174100.extcsd
26/07/2019 17:41:00> EMMC Init completed.
26/07/2019 17:41:00>
26/07/2019 17:41:00> Get firmware version
26/07/2019 17:41:00>
26/07/2019 17:41:09> Brand = samsung
26/07/2019 17:41:09> Manufacturer = samsung
26/07/2019 17:41:09> Device = grandpplte
26/07/2019 17:41:09> Model = SM-G532G
26/07/2019 17:41:09> Phone platform = mt6737t
26/07/2019 17:41:09> CPU Abi = armeabi-v7a
26/07/2019 17:41:09> Mediatek platform = MT6737T
26/07/2019 17:41:09> Android release = 6.0.1
26/07/2019 17:41:09> Firmware version = MMB29T.FA60_G532GDXU1AQJ1
26/07/2019 17:41:09> Firmware date = Tue Oct 17 13:47:33 KST 2017