[eivelice]

type of connection is via moorc adapter 5 in 1

box type is i really don't know, i bought this box in 2017.. its an old one not yet easy jtag plus but i updated it to plus.

EasyJtag Suite Classic ver.: 3.6.1.15 / wxWidgets 3.1.2-W-U started.
OS ver.: Windows 7 (build 7601, Service Pack 1). Admin rights OK
Android Explorer ver:1.0.0.13
Autorun Agent ver:1.0.0.0
Crash Reporting ver:1.4.0.3
eMMC Odin ver:1.0.0.6
QUALCOMM Direct ver:1.0.6936.8894
Android ADB API ver:2.0.0.0
FTDI API ver:3.2.4.0
LibUSB API ver:1.2.6.0
Visual C++ Runtime ver:10.0.30319.1
Setting box Pinout ...

Box Drivers version: 3.0.1.0, are OK
Z3X Card Serial : AA69-xxxx , ver: 22
Z3X Card Activation [JTAGPLUS] : NOT ACTIVATED
Z3X Card Activation [LG] : NOT ACTIVATED
Z3X Card Activation [SAMS] : NOT ACTIVATED
Z3X Card Activation [JTAG] : ACTIVATED

i tried this now : universal format

and i have resoldered all wires

Running:eMMC: Factory Format
Z3X EasyJtag Software ver. 3.6.1.15
Skip loading eMMC Addon Firmware
CMD Pullup Level:2928 mV
CMD Active Level:3217 mV
Box IO Level:3300 mV
CLK Rate:14000 kHz
Formatting eMMC card, please wait up to 3 min...
Setting Service Mode...
eMMC Format Done.

Done.

and then i try to write all roms again using the 2 file from support with only charger in phone. with 3.3v and 21 mhz clk

and this is logs :

Done.
Checking NAND Image : C:\emmc file repair jtag\g532g\SAMSUNG_SM-G532G_emmc_dump_ROM1_ROM2_200MB\Samsung_SM-G532G_emmc_dump_ROM1.bin
Autodetected RAW data
Partition info successfully found
Linux partitions is not found in image...
File successefuly loaded!

Found ROM2 and automatically selected.
extCSD Are not selected , skip writing extCSD
Processing file...C:\emmc file repair jtag\g532g\SAMSUNG_SM-G532G_emmc_dump_ROM1_ROM2_200MB\Samsung_SM-G532G_emmc_dump_ROM1.bin
Processing file...C:\emmc file repair jtag\g532g\SAMSUNG_SM-G532G_emmc_dump_ROM1_ROM2_200MB\Samsung_SM-G532G_emmc_dump_ROM2.bin
ROM3 Are not selected , skip writing ROM3
Z3X EasyJtag Software ver. 3.6.1.15
Skip loading eMMC Addon Firmware
CMD Pullup Level:2928 mV
CMD Active Level:3217 mV
Input file : C:\emmc file repair jtag\g532g\SAMSUNG_SM-G532G_emmc_dump_ROM1_ROM2_200MB\Samsung_SM-G532G_emmc_dump_ROM1.bin
Writing 000AC00000 bytes to 0000000000... ROM1 (USER ROM)
Error writing address 0x03000000 Error Code:-1 Reason :CMD Timeout Error
Retry writing address 0x0003000000 (Attempt #1)...
Retry Success!
Error writing address 0x06800000 Error Code:-1 Reason :CMD Timeout Error
Retry writing address 0x0006800000 (Attempt #1)...
Retry Success!
Done, time taken: 123 sec. Average Write Speed: 1464 kB/s

Z3X EasyJtag Software ver. 3.6.1.15
Skip loading eMMC Addon Firmware
CMD Pullup Level:2928 mV
CMD Active Level:3217 mV
Input file : C:\emmc file repair jtag\g532g\SAMSUNG_SM-G532G_emmc_dump_ROM1_ROM2_200MB\Samsung_SM-G532G_emmc_dump_ROM2.bin
Writing 0000200000 bytes to 0000000000 ...ROM2 (BOOT1 ROM)
Done, time taken: 2 sec. Average Write Speed: 703 kB/s

but when i detect the phone again after writing rom, this is the logs :

there is an error see logs :

Z3X EasyJtag Software ver. 3.6.1.15
Loading eMMC GEN1 Firmware... IO: 3300 mV
Box S/N: 12FF9016CE5F1172, ,FW Ver.: 01.63
CMD Pullup Level:2939 mV
CMD Active Level:3238 mV
Box IO Level:3300 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is ON!
---------- eMMC Device Information ----------

eMMC CID : 90014A483847347592010B5A3088A40C
eMMC CSD : D02701320F5903FFFFFFFFE78A40002A
eMMC Manufacturer ID: 0090 , OEM ID: 014A
eMMC Date: 10/2017 Rev.0x1
eMMC NAME: H8G4u , S/N: 190460040
eMMC NAME (HEX): 483847347520
EMMC ROM1 (Main User Data) Capacity: 7456 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC RPMB is programmed and written 0 times
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.7 (MMC 5.0)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00002000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: H8G4u_ 190460040_20191109_1755.extcsd
Caution: invalid backup GPT header, but valid main header!
Warning! Main and backup partition tables differ!
Warning! One or more CRCs don't match. You should repair the disk!
Caution: Found protective or hybrid MBR and corrupt GPT.
Real (Hardware) Disk/Image size: E90000 sectors 7.3 GiB
Soft (Partitioned) Disk/Image size: E8FFBC sectors 7.3 GiB
Disk identifier (GUID): 98101B32-BBE2-4BF2-A06E-2BB33D000C20
Logical sector size: 0x200 bytes ,First/Last usable sector: 34,15269854
Partition info successfully found
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x000C000000 (3.7GB)
Unable to mount SYSTEM , code : 95
---------------------------------------------
Detected USERDATA USERDATA : 0x00E9400000 (3.632GB)
Unable to mount USERDATA , code : 95
Done.

then i go to easy jtag plus for write by vendor and this is logs:

eMMC_tool Suite ver. 1.6.2.0 (release date: 30.06.2019)
Microsoft Windows 7 (32 bit) build 7601 (6.1.7600.16385)

Looking for EasyJTAG box...
EasyJTAG API ver. 3307
EasyJTAG Box Serial = 12FF9016CE5F1172
Card Serial = AA699FF3
EasyJTAG Box Firmware = 1.63

Changelog:

30.06.2019 (ver 1.6.1.0)
Fix: Bugs that have been found through your crash report

HiPower mode is ON
Setting frequence to 21 MHz
CMD Pullup Level: 2939 mV
CMD Active Level: 3227 mV
EMMC Device Information :
EMMC CID: 90014A483847347592010B5A3088A40C
EMMC CSD: D02701320F5903FFFFFFFFE78A40002A
EMMC Manufacture : SKHYNIX , EMMC NAME: H8G4u , HEX: 483847347500 , S/N: 0B5A3088 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 10/2017
EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 0 , Response: Maybe not clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H8G4u_0B5A3088_20191109_175746.extcsd
EMMC Init completed.

Opening file: GRANDPPLTE_CIS_SER.pit

Pit: GRANDPPLTE_CIS_SER.pit
Entry count: 34

The size of the last section has been updated

BL_G532GDXU1AQI2_CL12327063_QB15069235_REV00_user_ low_ship_MULTI_CERT.tar.md5
The list of files in the firmware:
preloader.img
lk.bin
param.bin
trustzone.bin
efuse.img

HiPower mode is ON
Setting frequence to 21 MHz
CMD Pullup Level: 2939 mV
CMD Active Level: 3238 mV
EMMC Device Information :
EMMC CID: 90014A483847347592010B5A3088A40C
EMMC CSD: D02701320F5903FFFFFFFFE78A40002A
EMMC Manufacture : SKHYNIX , EMMC NAME: H8G4u , HEX: 483847347500 , S/N: 0B5A3088 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 10/2017
EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 0 , Response: Maybe not clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H8G4u_0B5A3088_20191109_175758.extcsd
EMMC Init completed.

Operation: Write by vendor (Samsung)

Creating GPT-partitioninig
Writing PrimaryGPT at address: 000000000000
Writing BackupGPT at address: 0001D1FFBE00
Writing PIT at address: 000000004400
GPT-partitioning done

Unpacking file: preloader.img
Unpacking file: lk.bin
Unpacking file: efuse.img
Unpacking file: trustzone.bin
Unpacking file: param.bin

Partition name: BOOTLOADER
Filename: preloader.img , Offset: 000000000000 , filesize: 170240 bytes
eMMC switching to ROM2
Erasing partition...
Writing partition...
Done writing partition. Write speed: 330.89 KB/s
Partition name: LK
Filename: lk.bin , Offset: 000001000000 , filesize: 590336 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 490.43 KB/s
Partition name: EFUSE
Filename: efuse.img , Offset: 000001B80000 , filesize: 768 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 56.12 KB/s
Partition name: TEE1
Filename: trustzone.bin , Offset: 000001C00000 , filesize: 324352 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 836.97 KB/s
Partition name: PARAM
Filename: param.bin , Offset: 000005000000 , filesize: 747520 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 863.14 KB/s

Partition CACHE : formatting as EXT4. Please wait ...
Formatting completed
Partition HIDDEN : formatting as EXT4. Please wait ...
Formatting completed

Check BootConfig for the selected vendor

All done time: [00:00:31:611]

but phone still dead.

what do i need to do next please?

thank you

ALSO, when i try to do hw partition to write to extCSD

this is error :

Running:JEDEC: Partitions config burn...
Z3X EasyJtag Software ver. 3.6.1.15
Skip loading eMMC Addon Firmware
CMD Pullup Level:2939 mV
CMD Active Level:3238 mV
Box IO Level:3300 mV
CLK Rate:14000 kHz
GP Multiplier: 400000, 4096 Kb, 4Mb
Partition configuration:
No enhanced user data area
User partition write reliability: off
No GP1 partition
GP1 write reliability: on
No GP2 partition
GP2 write reliability: on
No GP3 partition
GP3 write reliability: on
No GP4 partition
GP4 write reliability: on
All GP Partitions are 0 set size of at least one GP Partition
HW Parts Config Fail.