View Single Post
Old 11-22-2019, 13:12   #61222 (permalink)
chadzar
No Life Poster
 
chadzar's Avatar
 
Join Date: Nov 2015
Location: DHAKA
Posts: 625
Member: 2489690
Status: Offline
Thanks Meter: 250
tecno sa7s read firmware and flashing done

Card found : F21468FB , v0138
Infinity-Box Chinese Miracle II : SPD/USC Module [SP2] v2.02

Load IDBase v10107 Ok!


Operation : Read FW [ v2.02 ]

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...


Device not found!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect Power/Cable!

Operation : Read FW [ v2.02 ]

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC7731E_BASE : SC7731E_eMMC_512MB_RS
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : Control transfered!

Boot Done!


Error : Device NOT INITIALIZED ! Initialize it first via "IDENTIFY" !
Make sure you have made "IDENTIFY" first!

Reconnect Power/Cable!

Operation : Identify [ v2.02 ]

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC7731E_BASE : SC7731E_eMMC_512MB_RS
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : Control transfered!

Boot Done!

Device info :
Patch Level : OPM2.171019.012
Display ID : SA7S-SA331-8.1-ZA-Voda-V010-20181122
Ver. CodeName : REL
Ver. Release : 8.1.0
Sec. Patch : 2018-11-05
Build Time : 1542938152
Product Model : TECNO SA7S
Product Brand : TECNO
Product Name : SA331
Product Device : TECNO-SA7S
Product Manfct : TECNO MOBILE LIMITED
Product Info : TECNO SA7S
Product Board : sp7731e_1h20
Board Platform : sp7731e

Update DataBase ...


Platform Version: MOCORTM_17C_W18.31.2_P6_Debug
Project Version: pike2_pub
BASE Version: FM_BASE_17C_W18.31.2_P6
HW Version: sc7731e_modem
CMP_Time : 11-15-2018 16:42:42

MODEM TAG : MOCORTM_17C_W18.31.2_P6_Debug_FM_BASE_17C_W18.31.2 _P6_sc7731e_modem_pike2_pub

UserData : STATE : PLAIN


Done!
Elapsed: 00:03:20

Operation : Read FW [ v2.02 ]

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC7731E_BASE : SC7731E_eMMC_512MB_RS
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : Control transfered!

Boot Done!

Device info :
Patch Level : OPM2.171019.012
Display ID : SA7S-SA331-8.1-ZA-Voda-V010-20181122
Ver. CodeName : REL
Ver. Release : 8.1.0
Sec. Patch : 2018-11-05
Build Time : 1542938152
Product Model : TECNO SA7S
Product Brand : TECNO
Product Name : SA331
Product Device : TECNO-SA7S
Product Manfct : TECNO MOBILE LIMITED
Product Info : TECNO SA7S
Product Board : sp7731e_1h20
Board Platform : sp7731e

VlnrLevel : 0x02

SP7731E__TECNO_MOBILE_LIMITED__TECNO_SA7S__8.1.0__ SA7S-SA331-8.1-ZA-Voda-V010-20181122__OPM2.171019.012__TECNO_SA7S

Read : u-boot.bin
Read : sml.bin
Read : tos.bin
Read : vbmeta.img
Read : deltanv_w.bin
Read : pm_sys.bin
Read : modem_w.bin
Read : gdsp_w.bin
Read : nvitem_w.bin
Read : modem_wcn.img
Read : gnssmodem.bin
Read : gnssbdmodem.bin
Read : boot_logo.bmp
Read : fastboot_logo.bmp
Make : persist.img
Read : phase.cfg
Read : boot.img
Read : recovery.img
Read : system.img
ExtSparse : Compression ratio : 92%
Read : vendor.img
ExtSparse : Compression ratio : 87%
Make : userdata.img
Make : cache.img
Read : prodnv.img
ExtSparse : Compression ratio : 51%
Read : u-boot-spl.bin

Firmware size : 0x566A3080 ( 1.35 GiB )
Android Info saved : _Android_info.txt
Reconnect Power/Cable!


Done!
Elapsed: 00:41:37

Open : SPD_PROG.xml
Reading package ...
Read package finished!

Created by Infinity-Box (c) 2019
Chinese Miracle II : Spreadtrum / UniSoc Service Module
Device Info file : _Android_info.txt

Patch Level : OPM2.171019.012
Display ID : SA7S-SA331-8.1-ZA-Voda-V010-20181122
Ver. CodeName : REL
Ver. Release : 8.1.0
Sec. Patch : 2018-11-05
Build Time : 1542938152
Product Model : TECNO SA7S
Product Brand : TECNO
Product Name : SA331
Product Device : TECNO-SA7S
Product Manfct : TECNO MOBILE LIMITED
Product Info : TECNO SA7S
Product Board : sp7731e_1h20
Board Platform : sp7731e


Operation : Flash Firmware [ v2.02 ]

Setting : Update NVRAM : False
Setting : Force NVRAM : False
Setting : Update PMT : True

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...


Device not found!
Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect Power/Cable!

Operation : Flash Firmware [ v2.02 ]

Setting : Update NVRAM : False
Setting : Force NVRAM : False
Setting : Update PMT : False

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC7731E_BASE : SC7731E_eMMC_512MB_RS
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : Control transfered!

Boot Done!

UBOOT : u-boot.bin
UBOOT : u-boot.bin
CODE : sml.bin
CODE : sml.bin
CODE : tos.bin
CODE : tos.bin
CODE : vbmeta.img
CODE : vbmeta.img
CODE : deltanv_w.bin
CODE : pm_sys.bin
CODE : modem_w.bin
CODE : gdsp_w.bin
ERASE : FLASH_W
CODE : modem_wcn.img
CODE : gnssmodem.bin
CODE : gnssbdmodem.bin
CODE : boot_logo.bmp
CODE : fastboot_logo.bmp
FSIMG : persist.img
ERASE : MISC
CODE : boot.img
CODE : recovery.img
FSIMG : system.img
FSIMG : vendor.img
FSIMG : userdata.img
FSIMG : cache.img
FSIMG : prodnv.img
ERASE : UBOOT_LOG
UBOOT : u-boot-spl.bin

Flashing finished!

Reconnect Power/Cable!


Done!
Elapsed: 00:07:07
  Reply With Quote
The Following 2 Users Say Thank You to chadzar For This Useful Post:
 
Page generated in 0.11904 seconds with 6 queries