View Single Post
Old 10-30-2007, 19:31   #1 (permalink)
brain00000
Freak Poster
 
Join Date: Oct 2006
Posts: 293
Member: 364696
Status: Offline
Thanks Meter: 16
Need Help DVD S618

hi Team I gov a Chinese mobile with lable Dvd S618
it start like this
when we power on, it shows counting 1..100 then gose off
when get full info its ok
OM3 [VCP0] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: NAND reset
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6228:8A02:8A02]...
chip-id: 0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.1
NAND: Samsung K9F1G08X0M 2048+64 64 pages, 132Mb
NAND id: ECF18015
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00EC:00F100800015 [08400000]
warning: NOR flash chip not supported or not detected
Initialize Done
Set baud...
230400
Set baud Done
Identification...
converting data...
done
protocol ver: 04
ver. sw1: SHINEC28_06A_PCB04_GPRS_MT6228_S02.SHINEC_S2_IL922 1_V2_2.BIN
ver. sw2: SHINEC_S2_IL9221_V2.2
ffs offset/size: 02000000/06000000
id-page Ok
nfi area detection finished: Ok
structure: 2nd [enhanced] (or higher) generation
identification data Ok
identification data backup saved: id.27EADFDB.[SHINEC28_06A_PCB04_GPRS_MT6228_S02.SHINEC_S2_IL922 1_V2_2.BIN_B202C57C].rpl
New firmware detected: SHINEC28_06A_PCB04_GPRS_MT6228_S02.SHINEC_S2_IL922 1_V2_2.BIN
- make "Read detailed information" operation
- send "backup_system_log_..." file to support
- make "Read full flash" operation
- send flash backup file(s) to support
- include in your e-mail full text from phone back label (phone name etc.)
identification detection finished
Identification Done
Manipulation...
Manipulation Done
Finalization...
Finalization Done
Write...
formatting...
Write Done
file saved: backup_system_log_27EADFDB_SHINEC28_06A_PCB04_GPRS _MT6228_S02.SHINEC_S2_IL9221_V2_2.BIN_B202C57C_200 71029-103300.B4X.bin
Finished, time used: 78 sec
Remove/Install battery now !

safe form
COM3 [VCP0] selected
Phone should be Switched OFF !
Press and HOLD Power button now !
19200
Initializing[6228:8A02]...
Connecting, wait...
error: can't finalize test moide
Operation failed !
Finished, time used: 21 sec
Remove/Install battery now !

it format complete ok after complete formatting phone is in same position
but when we get detailes info it gives
COM3 [VCP0] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: read/check detailed information
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6228:8A02:8A02]...
chip-id: 0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.1
NAND: Samsung K9F1G08X0M 2048+64 64 pages, 132Mb
NAND id: ECF18015
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00EC:00F100800015 [08400000]
warning: NOR flash chip not supported or not detected
Initialize Done
Set baud...
230400
Set baud Done
Identification...
converting data...
done
protocol ver: 04
ver. sw1: SHINEC28_06A_PCB04_GPRS_MT6228_S02.SHINEC_S2_IL922 1_V2_2.BIN
ver. sw2: SHINEC_S2_IL9221_V2.2
ffs offset/size: 02000000/06000000
id-page Ok
nfi area detection finished: Ok
structure: 2nd [enhanced] (or higher) generation
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
error: unexpected answer:
identification data damaged
identification detection finished
Finished, time used: 263 sec
Remove/Install battery now !
now can i flash it
  Reply With Quote
 
Page generated in 0.25926 seconds with 6 queries