Quote:
Originally Posted by joni_rajpura  Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
see near cpu mt6226 then u found there flesh ic rehoot or rebool ic
now com to topic power consuming
i also se 9 phone with same models with 1 gb internel memory when i try to
format these phone same error comes damage flesh chip and after that
phone is going to same poosition as yours so rebool flesh solve you problam
rebool and post result there
best of luck  |
gud shot bro.. i heated the chip and fone started to boot.. here is the log
COM46 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: reset
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:22E2:1A39
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: B0001D00000000:B0001D00000000
flash: Sharp Intel/Sharp ext [def 0004x008000 007Fx020000] 16Mb
detecting chip #01 in region #00...
flash: B0001D00000000:B0001D00000000
flash: Sharp Intel/Sharp ext [def 0004x008000 007Fx020000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
115200
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: B0001D00000000:B0001D00000000
flash: Sharp Intel/Sharp ext [def 0004x008000 007Fx020000] 16Mb
detecting chip #01 in region #00...
flash: B0001D00000000:B0001D00000000
flash: Sharp Intel/Sharp ext [def 0004x008000 007Fx020000] 16Mb
it's time to stop: 2A0000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.30CBF139.[MY6226_PCB01_GPRS_MT6226_S01.DM402_V007_WMB_2BT_GK W.BIN_D67C4850].rpl
identification#1 detection finished
device-id: 30CBF139
identification#1 protocol ver: 04
ver. sw1: MY6226_PCB01_GPRS_MT6226_S01.DM402_V007_WMB_2BT_GK W.BIN
ver. sw2: DM402.V007.WMB.2BT.GKW, AFB78329
ffs offset/size: 00F00000/00100000
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00F00000
flash: B0001D00000000:B0001D00000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00F00000
detecting eeprom/ffs size...
eeprom/ffs size: 00100000
ffs chip: 00
eeprom/ffs area: 00000000:00F00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading [eeprom[MY6226_PCB01_GPRS_MT6226_S01.DM402_V007_WMB_2BT_GK W.BIN]]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_eeprom[MY6226_PCB01_GPRS_MT6226_S01.DM402_V007_WMB_2BT_GK W.BIN]_20080423-155651.B0E.bin
flash: B0001D00000000:B0001D00000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
Write Done
Finalization...
formatting...
flash: B0001D00000000:B0001D00000000
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log _30CBF139_MY6226_PCB01_GPRS_MT6226_S01.DM402_V007_ WMB_2BT_GKW.BIN_D67C4850_20080423-155741.B0X.bin
Finished, time used: 293 sec
Remove/Install battery now !
File system has been modified !
It is need to press and HOLD phone "Power" button
during long time (up to 1 min) to make phone Powered-On !
but aftere that the fone is still dead.. what shud i do now??