View Single Post
Old 12-25-2008, 22:48   #1 (permalink)
e-gsmshop
No Life Poster
 
Join Date: Nov 2005
Posts: 618
Member: 203445
Status: Offline
Thanks Meter: 48
Anything for this please ?

COM5 [VCP0] selected
module v2.69
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read eeprom
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A03:8A00]...
CPU: MT6225
high speed boot enabled
chip: 0001:3903:0004
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 2088C4FFFFFFFF:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
detecting chip #01 in region #00...
flash: 2088C4FFFFFFFF:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud ...
230400
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: 2088C4FFFFFFFF:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
detecting chip #01 in region #00...
flash: 2088C4FFFFFFFF:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
it's time to stop: 18F09FE518F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 protocol ver: 04
ver. sw 1: S9.XYDL.T1.F0.U1.L8.V3.01.BIN
ver. sw 2: S9.XYDL.T1.F0.U1.L8.V3.01, 00000000
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: 2088C4FFFFFFFF:2088C400000000
checking area [00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00440000
Detected eeprom/ffs address is non-standard: 00440000
Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)

If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation

Are you sure that detected eeprom address is correct ?
Do you want to use standard eeprom address: 00E00000 ?

If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
terminated by user
error: critical error#1 during ffs size detection
error: can't detect eeprom/ffs address/size
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
Finished, time used: 81 sec
Remove/Install battery now !
BR

e-gsmshop
  Reply With Quote
 
Page generated in 0.14723 seconds with 6 queries