View Single Post
Old 12-31-2008, 08:03   #1 (permalink)
basilbaby
Freak Poster
 
basilbaby's Avatar
 
Join Date: Apr 2006
Posts: 307
Member: 263709
Status: Offline
Thanks Meter: 327
China clone 6500s-1 Rm-240 pinout....

China clone 6500s-1 Rm-240 pinout....




Quote:
CPU: MT6225
high speed boot On
chip: 0001:B603:0008
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: EC257E25082501:18A59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:18A59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: EC257E25082501:18A59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:18A59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: 18B09FA518B09FA518B09FA518B09FA518B09FA518B09FA5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: EC257E25082501:18A59F00000000
checking area [00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E20000
Detected eeprom/ffs address is non-standard: 00E20000

Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)

If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation

Are you sure that detected eeprom address is correct ?
autodetected eeprom/ffs address confirmed by user: 00E20000
detecting eeprom/ffs size...
eeprom/ffs size: 001E0000
ffs chip: 00
eeprom/ffs area: 00000000:00E20000-00FFFFFF
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: EC257E25082501:18A59F00000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
Write Done
Finalization ...
formatting...
flash: EC257E25082501:18A59F00000000
Finalization Done
Finished, time used: 190 sec
Remove/Install battery now !
Attached Images
File Type: jpg 6500S cina blk.jpg (61.5 KB, 296 views)
  Reply With Quote
The Following User Says Thank You to basilbaby For This Useful Post:
 
Page generated in 0.15551 seconds with 7 queries