[bencebacsi]

That was a good working phone. I read the firmware succesfully, but when I try to write back, Chinese Miracle reports flash write error. Whole flash chip or other format methods can be processed succesfully. I downloaded the firmware for this phone from support area, but the same result. I tried to connect with test point inside, but same result. I tried to use Spiderman and Infinity PinFinder too for flashing. The flash chip is empty now because the whole flash formatting. This is the log of my last trying:

COM14 [VCP1] selected
module v2.76
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A05:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:8C03:000C
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 98000300000000:FFFFFF00000000
flash: AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
detecting chip #01 in region #00...
flash: 98000300000000:FFFFFF00000000
flash: AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
detecting chip #02 in region #00...
flash: 98000300000000:FFFFFF00000000
flash: AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
detecting chip #03 in region #00...
flash: 98000300000000:FFFFFF00000000
flash: AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
number of flash chip/regions detected: 04/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. .................................................. .................................................. .................................................. ......
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. .................................................. .................................................. .................................................. ......
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
detecting security area (code #2)...
security area (code #2) is absent
Area: Firmware
flash: 98000300000000:FFFFFF00000000
Write: Firmware
error: error# 0000FFFF
error: flash write error: 00000000:00002000
error: error# 0000FFFF
error: flash write error: 00000000:00002000
error: error# 0000FFFF
error: flash write error: 00000000:00002000
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
Write Fail
Finished, time used: 143 sec
Remove/Install battery now !


After flashing hundrets of mobile phones with Chinese Miracle, this was the first occasion, when it killed a phone. Please, help me.