hang but now no power sir
try to format
forget to read fullflash
i need to revive this
COM67 [VCP0] selected
module v2.81
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
ffs/eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A03:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:B403:000D
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 01227E22202200:FFBFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:FFBFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #02 in region #00...
flash: 01227E22202200:FFBFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #03 in region #00...
flash: 01227E22202200:FFBFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 04/01
Initialize Done
Set baud ...
115200
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: 01227E22202200:FFBFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:FFBFFF00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: FFBFFFBFFFBFFFBFFFBFFFBFFFBFFFBFFFBFFFBFFFBFFFBF
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. .................................................. .................................................. .................................................. ......
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
detecting ffs/eeprom area in 1 chip(s)...
standard ffs/eeprom offset assigned: 00E00000
flash: 01227E22202200:FFBFFF00000000
checking area [00000000]: 00000000-00FFFFFF...
Can't detect ffs/eeprom area
Do you want to use standard ffs/eeprom address: 00E00000 ?
If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
operation terminated by user
error: critical error#1 during ffs/eeprom size detection
error: can't detect ffs/eeprom address/size
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: 01227E22202200:FFBFFF00000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. .................................................. .................................................. .................................................. ......
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\id.15C737A1.[MT256_TH_PCB01_GPRS_MT6225_S00.MT256_TH_0716_MP_V0 7.BIN_3A59B23E].rpl
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\id.15C737A1._MT25 6_TH_PCB01_GPRS_MT6225_S00.MT256_TH_0716_MP_V07.BI N_3A59B23E_.rpl
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.15C737A1.[MT256_TH_PCB01_GPRS_MT6225_S00.MT256_TH_0716_MP_V0 7.BIN_3A59B23E].rpl
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.15C737A1._MT256_TH_PCB01_GPRS_MT6225_S00.MT256_T H_0716_MP_V07.BIN_3A59B23E_.rpl
====================
warning: unknown identification#1 structure: MT256_TH_PCB01_GPRS_MT6225_S00.MT256_TH_0716_MP_V0 7.BIN_3A59B23E
error: Unknown firmware detected (v.2.81, database date: ), user action required:
1. download latest software from support area and try again
2. if no still luck follow the next procedure:
- find good working phone with the same firmware:
MT256_TH_PCB01_GPRS_MT6225_S00.MT256_TH_0716_MP_V0 7.BIN
- make "Read full flash" operation
- send "system_log_..." file to support:
[email protected]
- send flash backup files to support:
[email protected]
- include in your e-mail full text from phone back label (phone name etc.)
- be little bit patient and wait update
====================
detecting security area (code #2)...
security area (code #2) is absent
Area: Firmware
flash: 01227E22202200:FFBFFF00000000
Write: Firmware