[geovicky]

hello mate

i have chines Gaoxinqi dead now ineed flash file here is log

module v2.81
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection disabled
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
ffs/eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A03:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:5D03:000A
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 01227E22202200:18A59F00000000
flash: Amd PL127J D 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:18A59F00000000
flash: Amd PL127J D 16Mb
detecting chip #02 in region #00...
flash: 01227E22202200:18A59F00000000
flash: Amd PL127J D 16Mb
detecting chip #03 in region #00...
flash: 01227E22202200:18A59F00000000
flash: Amd PL127J D 16Mb
number of flash chip/regions detected: 04/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: 01227E22202200:18A59F00000000
flash: Amd PL127J D 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:18A59F00000000
flash: Amd PL127J D 16Mb
it's time to stop: 18B09FA518B09FA518B09FA518B09FA518B09FA518B09FA5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. .................................................. .................................................. .................................................. ......
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
detecting ffs/eeprom area in 1 chip(s)...
standard ffs/eeprom offset assigned: 00E00000
flash: 01227E22202200:18A59F00000000
checking area [00000000]: 00000000-00FFFFFF...
Can't detect ffs/eeprom area
Do you want to use standard ffs/eeprom address: 00E00000 ?
If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
standard ffs/eeprom address selected by user
detecting ffs/eeprom size...
ffs/eeprom size: 00200000
ffs/eeprom chip: 00
ffs/eeprom area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
reading: _ffs...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\_ffs_20090510-130702.B0E.bin
flash: 01227E22202200:18A59F00000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. .................................................. .................................................. .................................................. ......
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
detecting security area (code #2)...
security area (code #2) is absent
Area: Firmware
flash: 01227E22202200:18A59F00000000
Write: Firmware
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
Write Done
Finalization ...
Finalization Done
Finished, time used: 1260 sec
Remove/Install battery now !