Hello,
Same result ...
Unlock method : standard
COM5 [VCP0] selected
module v2.83
Device: Nexian-NX-G700
Checking data, wait...
advanced flash detection enabled
Action: "sp-unlock"
unlock method: standard
ffs/eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6223:8A05:8A00]...
CPU: MT6223
chip: 0011:AA21:000C
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 2088C4FFFFFFFF:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud ...
921600
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 detection finished
identification#1 protocol ver: 05
ver. sw 1: TINNO23C_08A_GEMINI_PCB01_GPRS_MT6223P_S00.E201B_F M_PR1_IN_V0_7.BIN
ver. sw 2: E201B_FM_PR1_IN_V0.7, 00000000
ffs offset/size: 00E00000/001F8000
ffs address assigned: 00E00000
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
sim-lock status: unknown
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
reading: Nexian-NX-G700_TINNO23C_08A_GEMINI_PCB01_GPRS_MT6223P_S00.E2 01B_FM_PR1_IN_V0_7__ffs...
file saved: D:\Program Files\InfinityBox\MModule\Nexian-NX-G700_TINNO23C_08A_GEMINI_PCB01_GPRS_MT6223P_S00.E2 01B_FM_PR1_IN_V0_7__ffs_20090728-131325.B0E.bin
flash: 2088C4FFFFFFFF:2088C400000000
Backup required data Done
Patch required data ...
detection procedure, wait...
detection procedure completed
detection procedure, wait...
error: phone is not locked or unknown eeprom
Patch required data Done
Special operation ...
detecting parameters to apply patch area 0/...
.....
flash: 2088C4FFFFFFFF:2088C400000000
flash: 2088C4FFFFFFFF:2088C400000000
Write: area 0/1
error: no any expected answer
error: flash write error: 00140000:00002000
error: no any expected answer
error: flash write error: 00140000:00002000
error: can't write required area
error: area 0/ can not apply patch
Special operation Done
Write ...
error: no any expected answer
error: no any expected answer : wrong answer after chip id request
error: no any expected answer
error: no any expected answer
error: no any expected answer : wrong answer after chip cfi request
error: no any expected answer
error: no any expected answer : wrong answer after chip id request
Write Fail
Finished, time used: 416 sec
Remove/Install battery now !
Unlock method : smart fast
COM5 [VCP0] selected
module v2.83
Action: unlock
unlock method: smart fast
Model: Nexian-NX-G700
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6223:8A05:8A00]...
CPU: MT6223
chip: 0011:AA21:000C
status: FF
Connecting at 19200, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6223,E05
Date: 2000.00.00
Version: 1.0
Version: E201B_FM_PR1_IN_V0.7
Version: TINNO23C_08A_GEMINI_HW
80 byte(s) read
imei: 35332703064288
connection Ok
186 byte(s) read
reading data...
reading data #2...
reading data #4...
reading data #5...
WARNING ! Unknown lock structure !
Read flash and send to support:
[email protected]
error: operation failed !
Finished, time used: 32 sec
Remove/Install battery now !
unlock method : read codes
COM5 [VCP0] selected
module v2.83
Action: read codes
unlock method: read codes
Model: Nexian-NX-G700
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6223:8A05:8A00]...
CPU: MT6223
chip: 0011:AA21:000C
status: FF
Connecting at 19200, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6223,E05
Date: 2000.00.00
Version: 1.0
Version: E201B_FM_PR1_IN_V0.7
Version: TINNO23C_08A_GEMINI_HW
80 byte(s) read
imei: 35332703064288
connection Ok
186 byte(s) read
reading data #4...
reading data #5...
error: source data size is less than expected
error: operation failed !
Finished, time used: 10 sec
Remove/Install battery now !
unlock method : standard fast
COM5 [VCP0] selected
module v2.83
Device: Nexian-NX-G700
Checking data, wait...
advanced flash detection enabled
Action: "sp-unlock"
unlock method: standard fast
Unlock procedure can be faster if you skip ffs/eeprom area backup procedure.
Do you want to disable ffs/eeprom backup ?
ffs/eeprom backup disabled
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6223:8A05:8A00]...
CPU: MT6223
chip: 0011:AA21:000C
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 2088C4FFFFFFFF:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud ...
921600
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 detection finished
identification#1 protocol ver: 05
ver. sw 1: TINNO23C_08A_GEMINI_PCB01_GPRS_MT6223P_S00.E201B_F M_PR1_IN_V0_7.BIN
ver. sw 2: E201B_FM_PR1_IN_V0.7, 00000000
ffs offset/size: 00E00000/001F8000
ffs address assigned: 00E00000
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
sim-lock status: unknown
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: 2088C4FFFFFFFF:2088C400000000
Backup required data Done
Patch required data ...
.......................................
lock area found
.......................................
lock area found
Patch required data Done
Special operation ...
detecting parameters to apply patch area 0/...
.....
flash: 2088C4FFFFFFFF:2088C400000000
flash: 2088C4FFFFFFFF:2088C400000000
Write: area 0/1
error: no any expected answer
error: flash write error: 00140000:00002000
error: no any expected answer
error: flash write error: 00140000:00002000
error: can't write required area
error: area 0/ can not apply patch
Special operation Done
Write ...
error: no any expected answer
error: no any expected answer : wrong answer after chip id request
error: no any expected answer
error: no any expected answer
error: no any expected answer : wrong answer after chip cfi request
error: no any expected answer
error: no any expected answer : wrong answer after chip id request
error: can't detect chip at required chip base
error: no any expected answer
error: no any expected answer : wrong answer after chip id request
error: no any expected answer
error: no any expected answer
error: no any expected answer : wrong answer after chip cfi request
error: no any expected answer
error: no any expected answer : wrong answer after chip id request
error: can't detect chip at required chip base
Write Fail
Finished, time used: 293 sec
Remove/Install battery now !
thanks