| COM6 [VCP0] selected
module v3.16
Device: Autodetect 6205-6239 NOR
Checking data, wait...
advanced flash detection enabled
Action: write flash
"smart write" active
write: Firmware
MT6225_GEMINI_PCB01_GPRS_MT6225_S00.M6225_N58_BD_0 2_V03__fullflash_20100728-151152.B0M.bin
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
====> Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A05:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:4A03:000D
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
====> Initialize ...
detecting chip #00 in region #00...
flash: 2088C4FFFF0013:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
otp offset: 00FE0000
detecting chip #01 in region #00...
flash: 2088C4FFFF0013:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
otp offset: 00FE0000
detecting chip #02 in region #00...
flash: 2088C4FFFF0013:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
otp offset: 00FE0000
detecting chip #03 in region #00...
flash: 2088C4FFFF0013:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
otp offset: 00FE0000
number of flash chip/regions detected: 04/01
Initialize Done
====> Set baud ...
921600
Set baud Done
====> Initialize bootcode ...
Initialize bootcode Done
====> Check firmware integrity ...
usb bootloader detect...
..
usb bootloader detect (phase #2)...
..
usb bootloader (chip) is absent
searching rom info...
search rom info finished
rom info structure: 2nd [standard] generation
TCL-ID is absent
rom info detection finished
rom info ver: 04
sw version: MT6225_GEMINI_PCB01_GPRS_MT6225_S00.M6225_N58_BD_0 2_V01.BIN
project-id: M6225_N58_BD_02_v01, 00000000
code offset: 00000000
ffs offset/size [01]: 00E00000/00200000
rom info structure: 2nd [standard] generation
TCL-ID is absent
sec info (detailed) detection...
searching sec info#1...
.
search sec info#1 finished
Check firmware integrity Done
====> Check firmware content ...
Check firmware content Done
====> Backup required data ...
Backup required data Done
====> Patch required data ...
Patch required data Done
====> Special operation ...
Special operation Done
====> Write ...
sec info (fast) detection...
searching sec info#1...
.
search sec info#1 finished
usb bootloader (file) is absent
startup code area #1 check...
startup code area #1 fixed
detecting startup code area #2...
startup code area #2 is absent
Area: Firmware
flash: 2088C4FFFF0013:2088C400000000
Write: Firmware
usb bootloader (file) is absent
sec info (fast) detection...
searching sec info#1...
.
search sec info#1 finished
Write Done
====> Finalization ...
Finalization Done
Finished, time used: 11 min 24 sec
Remove/Install battery now ! |