View Single Post
Old 05-14-2011, 21:49   #13 (permalink)
connexion2005
Freak Poster
 
Join Date: Jan 2011
Posts: 352
Member: 1501506
Status: Offline
Thanks Meter: 47
Quote:
Originally Posted by legija View Post
As i know those are same phones -,))
Update! The GT-i9020 is capable of BRICK REPAIR with the Riff box as well! Just solder the points and flash both the bootloader and recovery under the resurrection option. Be sure to make a full backup of the phone first though just in case.

Also, you will need an adjustable power supply as opposed to using the battery or atleast I did. RIFF kept on picking up over 3.2 volts when it needed 2.8V with the battery. With a lot of tweaking, I was able to get the board down to the 2.80 volts it was looking for and it worked perfect. When finished, put the phone into download mode using a JIG and then flash the appropriate firmware.


[5/14/2011 1:19:02 PM] [START OPERATION_ID = DCC_READ_MEMORY]
[5/14/2011 1:24:25 PM] Open serial port...OK
[5/14/2011 1:24:25 PM] Connecting to the RIFF Box...OK
[5/14/2011 1:24:25 PM] Firmware Version: 1.23, JTAG Manager Version: 1.32
[5/14/2011 1:24:25 PM] Selected Resurrector: [Samsung I9023]
[5/14/2011 1:24:25 PM]
[5/14/2011 1:24:25 PM] Connecting to the dead body...OK
[5/14/2011 1:24:25 PM] Detected dead body ID: 0x1BA00477 - CORRECT!
[5/14/2011 1:24:25 PM] Set I/O Voltage reads as 2.83V, TCK Frequency is 18 MHz
[5/14/2011 1:24:25 PM]
[5/14/2011 1:24:25 PM] Resurrection sequence started.
[5/14/2011 1:24:25 PM] Establish communication with the phone...OK
[5/14/2011 1:24:25 PM] Initializing internal hardware configuration...OK
[5/14/2011 1:24:25 PM] Uploading resurrector data into memory...OK
[5/14/2011 1:24:25 PM] Starting communication with resurrector...OK
[5/14/2011 1:24:25 PM]
[5/14/2011 1:24:25 PM] Detected an Initialized FLASH1 Chip ID: 0x00EC/0x0050 (512MB)
[5/14/2011 1:24:25 PM]
[5/14/2011 1:24:25 PM] Reading FLASH1 address space from 0x00000000 to 0x1FFFFFFF
[5/14/2011 1:24:25 PM] Completed in 00:05:19.115 (Average Transfer Rate: 1694.29 kB/s)
[5/14/2011 1:24:25 PM] [FINISH OPERATION_ID = DCC_READ_MEMORY]

[5/14/2011 1:24:59 PM] [START OPERATION_ID = RESURRECT]
[5/14/2011 1:26:49 PM] Open serial port...OK
[5/14/2011 1:26:49 PM] Connecting to the RIFF Box...OK
[5/14/2011 1:26:49 PM] Firmware Version: 1.23, JTAG Manager Version: 1.32
[5/14/2011 1:26:49 PM] Selected Resurrector: [Samsung I9023]
[5/14/2011 1:26:49 PM]
[5/14/2011 1:26:49 PM] Connecting to the dead body...OK
[5/14/2011 1:26:49 PM] Detected dead body ID: 0x1BA00477 - CORRECT!
[5/14/2011 1:26:49 PM] Set I/O Voltage reads as 2.83V, TCK Frequency is 18 MHz
[5/14/2011 1:26:49 PM]
[5/14/2011 1:26:49 PM] Resurrection sequence started.
[5/14/2011 1:26:49 PM] Establish communication with the phone...OK
[5/14/2011 1:26:49 PM] Initializing internal hardware configuration...OK
[5/14/2011 1:26:49 PM] Uploading resurrector data into memory...OK
[5/14/2011 1:26:49 PM] Starting communication with resurrector...OK
[5/14/2011 1:26:49 PM]
[5/14/2011 1:26:49 PM] Detected an Initialized FLASH1 Chip ID: 0x00EC/0x0050 (512MB)
[5/14/2011 1:26:49 PM]
[5/14/2011 1:26:49 PM] Flashing the dead body...OK
[5/14/2011 1:26:49 PM] Resurrection complete!
[5/14/2011 1:26:49 PM] [FINISH OPERATION_ID = RESURRECT]
 
 
Page generated in 0.21103 seconds with 6 queries