GSM-Forum - View Single Post - N95 8gb dead after flash - (SOLVED

Advance-Box · 09-25-2011, 03:35

@java_killer

Follow this procedure step by step and you will have it working.

I assume you have FULL RPL backup since I see it in your logs... Anyway, let's begin!

1. Full Erase CMT 16 MB using ERASE Flash Function

2. Full Erase APE 256 MB usgin ERASE Flash Function

A shortcut for 1 and 2 is just to click the SCAN button inside the Erase Flash tab, then
put a check on the 2 flash chips found, then click ERASE.

3. Full Flash your phone using your latest 35.0.001 Firmware (MCU, PPM, CNT etc...)

* uncheck Backup Simlocks
* uncheck Backup RPL
* uncheck Factory Reset

--> Now Phone should be BLACK Screen, but scan phone works with 12345 imei...

4. Now Write your Backup RPL File to your Phone...

5. Now do Repair Simlocks (SL1 and SL2) function.

6. Now use "Stand Alone SX4" and write PM 1 and 309 from RM-320.pm

--> Now scan phone should show everything is ok, but phone should be BLANK Screen!

7. Now Flash one of the ENO file from ATF Support Site:

Install it to your PC, and usually you will find it installed here:
C:\Program Files\Nokia\Phoenix\Products\RM-320\

Flash 1 file only to your Phone,, this file: "rm320_ENO_x_2007wk45v0.020_sos.fpsx"

Just to make it clear, if you flash this file with MCU or PPM, you will FAIL
and you will need to start again at step 1... So just Manually put this
1 file into ATF Software and Flash your N95 8GB phone now with this
SINGLE Flash File.

Settings for Flashing:

* uncheck Backup Simlocks
* uncheck Backup RPL
* uncheck Factory Reset

--> Now you will get "Test Mode" on screen

8. Now flash the second ENO file to the phone, file name:
"normalize_susd_eno_aino_urel.fpsx"

Manually add the SINGLE file above in ATF Software and flash this
SINGLE file to your phone...

Flash Settings:

* uncheck Backup Simlocks
* uncheck Backup RPL
* uncheck Factory Reset

--> You will still get "Test Mode" on screen

9. Now Full Flash the phone again (MCU, PPM, CNT etc...)

Flash Settings:

* uncheck Backup Simlocks
* uncheck Backup RPL
* PUT A CHECK on Factory Reset

10. Now Phone SHOULD BE ok...

If phone is still not OK, then it means you did not follow properly my 10
steps above... or your phone have non software Problems already.

My 10 Steps are fully tested with my N95 8GB Test Phone so I can
guarantee to you that all the steps are accurate.

The Procedure above WORKS on ALL RAPIDOYAWE Based Phones (N95, N95 8GB, N82 etc...)

All you need is 2 ENO files and a full RPL Certificate Backup of the CMT and APE Subsystems.

09-25-2011, 03:35	#16 (permalink)
Advance-Box No Life Poster Join Date: Dec 2007 Posts: 7,598 Member: 651945 Status: Offline Thanks Meter: 20,118	@java_killer Follow this procedure step by step and you will have it working. I assume you have FULL RPL backup since I see it in your logs... Anyway, let's begin! 1. Full Erase CMT 16 MB using ERASE Flash Function 2. Full Erase APE 256 MB usgin ERASE Flash Function A shortcut for 1 and 2 is just to click the SCAN button inside the Erase Flash tab, then put a check on the 2 flash chips found, then click ERASE. 3. Full Flash your phone using your latest 35.0.001 Firmware (MCU, PPM, CNT etc...) * uncheck Backup Simlocks * uncheck Backup RPL * uncheck Factory Reset --> Now Phone should be BLACK Screen, but scan phone works with 12345 imei... 4. Now Write your Backup RPL File to your Phone... 5. Now do Repair Simlocks (SL1 and SL2) function. 6. Now use "Stand Alone SX4" and write PM 1 and 309 from RM-320.pm --> Now scan phone should show everything is ok, but phone should be BLANK Screen! 7. Now Flash one of the ENO file from ATF Support Site: Install it to your PC, and usually you will find it installed here: C:\Program Files\Nokia\Phoenix\Products\RM-320\ Flash 1 file only to your Phone,, this file: "rm320_ENO_x_2007wk45v0.020_sos.fpsx" Just to make it clear, if you flash this file with MCU or PPM, you will FAIL and you will need to start again at step 1... So just Manually put this 1 file into ATF Software and Flash your N95 8GB phone now with this SINGLE Flash File. Settings for Flashing: * uncheck Backup Simlocks * uncheck Backup RPL * uncheck Factory Reset --> Now you will get "Test Mode" on screen 8. Now flash the second ENO file to the phone, file name: "normalize_susd_eno_aino_urel.fpsx" Manually add the SINGLE file above in ATF Software and flash this SINGLE file to your phone... Flash Settings: * uncheck Backup Simlocks * uncheck Backup RPL * uncheck Factory Reset --> You will still get "Test Mode" on screen 9. Now Full Flash the phone again (MCU, PPM, CNT etc...) Flash Settings: * uncheck Backup Simlocks * uncheck Backup RPL * PUT A CHECK on Factory Reset 10. Now Phone SHOULD BE ok... If phone is still not OK, then it means you did not follow properly my 10 steps above... or your phone have non software Problems already. My 10 Steps are fully tested with my N95 8GB Test Phone so I can guarantee to you that all the steps are accurate. The Procedure above WORKS on ALL RAPIDOYAWE Based Phones (N95, N95 8GB, N82 etc...) All you need is 2 ENO files and a full RPL Certificate Backup of the CMT and APE Subsystems.