View Single Post
Old 04-12-2012, 18:38   #11 (permalink)
praji
Freak Poster
 
praji's Avatar
 
Join Date: Aug 2007
Location: in iOs
Posts: 454
Member: 563648
Status: Offline
Sonork: 100.1594523
Thanks Meter: 87
successfully flashed
Make sure USB cable, Battery and charger are removed from device.
Insert USB cable, Battery back to device(make sure to have fully charged battery).
Insert Charger or Press phone's power button(if flashing doesnt start automatically)
Waiting for USB ROM device ...
Device synchronized.
CPU: XGOLD 213
Using embedded SBL from MCU.
Sending EBL Loader...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.46
EBL version: Quantum_Bootloader_10.46_M1S1
Protocol version suggested by phone: 3
Set baud rate to: 6.50 Mbit/s
Flash ID: 0089 8982 - 23280001 [Intel NU48F512,512 Mbits]
CFI information:
Flash settings: 0/1024, size: 0x04000000
1 Block regions:
512 x 0x00020000 = 0x04000000
EBL ready !
Original IMEI: 35934504371146
RPL backup already exist (C:\mobileEx\3.5\data\backup\XGOLD_35934504371146_ back.RPL)
Processing file: rm761__11.56.mcusw
Downloading item CODE:rm761__11.56.mcusw_ebl_psi.fls, num block: 4, size: 25.25 MB
Erasing area 0x40000000-0x4001FFFE ...OK
Programming completed in 0.328 s
Erasing area 0x40040000-0x4005FFFE ...OK
Programming completed in 0.328 s
Erasing area 0x40060000-0x4015FFFE ...OK
Programming completed in 1.313 s
Erasing area 0x40280000-0x41A7FFFE ...OK
Programming completed in 27.672 s
Checksum verified (0xC6C7)
Processing file: rm761__11.56.ppm_mec
Downloading item CUSTackage_mec.ppm_ebl_psi.fls, num block: 1, size: 6.36 MB
Erasing area 0x41A80000-0x420DB47E ...OK
Programming completed in 7.469 s
Checksum verified (0xA9D8)
Processing file: rm761__11.56.image_mec_059J4L2_006
Downloading item CUSTackage_mec_059J4L2.image.fls, num block: 1, size: 14.50 MB
Erasing area 0x421C0000-0x43E1FFFE ...OK
Programming completed in 16.718 s
Checksum verified (0xBACC)
Total time for flashing process(boot+erase+write) was 7 min 15.344 s
Waiting for USB device removal ...OK
Waiting for USB device arrival ...
Waiting for device boot up ...
Device connected: nmwcdc\Nokia USB Phonet, PORT_ID: 207F2782
Verifying communication to device OK.


After Flash Processing ...


Phone type: RM-761 (Nokia 200)
SW version: V 11.56 26-03-12 RM-761 (c) Nokia
Imei plain: 35934504371146-0
Product code: 059J4L2
Cellular system: GSM
ASIC ID: 0x0000, type: 11
Ppm Id: MEC
Language Pack:
- not available.


Imei net: 35934504371146
Version: SIMLOCK SERVER
Provider: GSM Test Operator
Counter: 0/3, 0/10

CONFIG_DATA: 0010100000000000
PROFILE_BITS: 800000000003000B

BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
 
The Following User Says Thank You to praji For This Useful Post:
 
Page generated in 0.08224 seconds with 7 queries