View Single Post
Old 07-18-2012, 15:18   #7 (permalink)
moulnisky
No Life Poster
 
moulnisky's Avatar
 
Join Date: Jan 2009
Location: England
Age: 58
Posts: 17,681
Member: 947561
Status: Offline
Thanks Meter: 14,051
Quote:
Originally Posted by jatza View Post
Just have done full erase chip, but the phone is no longer detected via fbus.

Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102011104
CMT_EM_ASIC_ID: 00001040
CMT_EM_ASIC_ID: 00001030
CMT_PUBLIC_ID: 14D0010975400E49CE5178EE0A602065A1D9F871
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 25B977A055BE9B5DEC0C38A2A279C695
CMT_SECURE_ROM_CRC: 37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.11.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0020004000000031, ST, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x0020004000000031, ST, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00200040 (ST), Size: 256MBytes, VPP: Not Supported
FlashChip 0x00200040 (ST), Size: 256MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.11.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 85F252E351E225CAFC4DFBC8041EABD2823E3500
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
Erasing flash chip...
Started group flash erase
EraseArea[0,CMT]: 0x00000000-0x0FFFFFFF, ONENAND
Waiting 640s for erasure finish...
Erase taken 1.124s
Restarting MCU...
BB5 Full Erase Finished!
Started Phone Security Analysis...
Analyze Security Error -> Phone not detected (FBUS)
Failed to read info -> Phone not detected


OK, it's detected via USB
Obviously
When the mobile is fully erased can be seen only on the flashbus so you can see it doing "check flashing bus"
Full flash the mobile as indicated and afterward the mobile will get again the local mode

BR

Alex
 
 
Page generated in 0.07753 seconds with 7 queries