View Full Version : How to wrong code reset myx-5 new version!!!
!!!TaaTTalTi!!!
10-10-2003, 13:17
hi all friends!!
how to wrong code reset myx-5 new version not work test mode code!!!
thanks!!!
mr_x4you
10-13-2003, 11:41
Easy, read old posts... posted by wazl
!!!TaaTTalTi!!!
10-14-2003, 11:44
I'm searching old post not found topics!!!
pls help me!!!
chris922
10-14-2003, 11:50
If you write 3A F5 in your field 995 , the perm blocked error is gone ...
(This is only for your Phone... Others should not try this)
!!!TaaTTalTi!!!
10-14-2003, 18:39
hi chris
myx-3 hardware failure repair solution please
chris922
10-15-2003, 10:47
Another solution: After that the error message is gone:
Use a special connector: On Sagem side: Use PIN 6 and GND and then you need PIN 1 for the signal.
Connect PIN1 to the groung of your computer serial and PIN 6 you connect to PIN 8 on the computer side.
Now comes the tricky part:
You must connect a special hardware inteface to your Phone:
Use a standard 230V:12V trasformator, but connect the 230V side of it to the computer ground and the other contact to PIN 13 at the Phone.
Now you must be shure to avoid electical shock and ground yourself: You can must fasten a wire on your left hand and fasten the other end of the wire on electrical ground in your electrcal installation. The right hand you should connect with a wire to PIN 8 of the Sagem Phone. Now you can repair the Phone:
Start SagemDr connect to COM2 and select 19200 baud.
Try to read field 231, and when you get the error message, you must connect the 12V side of the transformator to your 230V installation.
If you only have a 110 V Network, you may have to repeat the procedure twice.
After that you cannot see the error message on your Phone anymore. And if evverything went good, the Sagemdoc does not show the eror message that field 231 cannot be read or written.
Have much fun :-)
!!!TaaTTalTi!!!
10-15-2003, 11:08
thanks chris922
chris922
10-15-2003, 11:19
It was a pleasure for me to help my best friend :-)
.:hack3r2k:.
10-15-2003, 11:39
:D
best regards,
.:hack3r2k:.
!!!TaaTTalTi!!!
10-15-2003, 12:05
:) :)
spectrum
10-15-2003, 18:56
You electrify your entire computer, your phone and get fried:rolleyes:
no no no
you get rid of SIM VERROU or SIM LOCKED message
I just tried ... and i'm still alive :)
but i triend with friend's my-x5m and his PC
I also used High-Voltage protection Gloves :)
:) :) :)
b.r.
ALex
You all are not sincere....!!! why are you all making it look as if its a bad solution..afterall the method is the only 10000% working solutiom,
I just tested on MYx6 and it worked 10000%
Carry on Volkangsm....:D :D :D
BR
Siemens man
10-21-2003, 22:55
hi guys
please show picture for solution, reset wrong counter
huh
i thought about this ... but i dont want others
watching me electrifying myself and my PC and sagem phone :)
b.r.
alex
!!!TaaTTalTi!!!
10-22-2003, 12:07
yes essojay go to school!!!
I'm very happy why!! My phone repairing %100 work but no chris922 solution!!! chris922 solution bad hehehe!!
haaa!!! Chris922 you thanks!!! but for not solution
hitibiti
10-23-2003, 01:41
any one have a nother easy solution
thx
Siemens man
10-25-2003, 01:17
need picture for solution
Siemens man
10-28-2003, 01:58
hi man
please help me. my phone is my x-3 hardware failure.
thank you Originally posted by volkangsm
yes essojay go to school!!!
I'm very happy why!! My phone repairing %100 work but no chris922 solution!!! chris922 solution bad hehehe!!
haaa!!! Chris922 you thanks!!! but for not solution
!!!TaaTTalTi!!!
10-28-2003, 11:20
sagem myx-3 repair hardware solution!!!
1 - Socket in charger
2- Backup eeprom
3- Phone off in chargered open sagem doctor
4- Backup field 268 and 268 (00 00) changed!!!
5- Open SagemWorkshop Denny Reset phone
6- And Open SagemDoctor write field 268 orginal value
7- Phone Push start ecran shoot simlocked and insert unlock code ok and wait 8 minute phone unlocked!!!
Thank you so much, it works!:D :D :D
good luck!!!!!
blaiseid
10-28-2003, 18:01
OOOpppssssssssss! Myself I can t try this method.Better a dead phone than Electrify myself.oopss!
You will tell me later!!!
Blaise
you can also use a litle bit of TNT pulver,works 1000000000% you will never more see hardvare failure
blaiseid
11-28-2003, 21:00
How to use the TNT PULVER?
BLAISE
byteforce
08-01-2005, 17:41
Does this work on MYX-5m ? and other Sagem models?
thanks in advance
Another solution: After that the error message is gone:
Use a special connector: On Sagem side: Use PIN 6 and GND and then you need PIN 1 for the signal.
Connect PIN1 to the groung of your computer serial and PIN 6 you connect to PIN 8 on the computer side.
Now comes the tricky part:
You must connect a special hardware inteface to your Phone:
Use a standard 230V:12V trasformator, but connect the 230V side of it to the computer ground and the other contact to PIN 13 at the Phone.
Now you must be shure to avoid electical shock and ground yourself: You can must fasten a wire on your left hand and fasten the other end of the wire on electrical ground in your electrcal installation. The right hand you should connect with a wire to PIN 8 of the Sagem Phone. Now you can repair the Phone:
Start SagemDr connect to COM2 and select 19200 baud.
Try to read field 231, and when you get the error message, you must connect the 12V side of the transformator to your 230V installation.
If you only have a 110 V Network, you may have to repeat the procedure twice.
After that you cannot see the error message on your Phone anymore. And if evverything went good, the Sagemdoc does not show the eror message that field 231 cannot be read or written.
Have much fun :-)
chris922
08-08-2005, 20:34
Hehe :)
Nice to see my old thread is still allive...
byteforce: Yes, this works with every phone, even with Nokia...
Even with yor TV-set, if it has the names pins somewhere...
But, perhapes you should carefully read it. The meaning is: "You cannot see the error message anymore" :cool:
And like schiavo mentioned: TNT will also work very good.
Greetings to all who know me :)
Chris
.:hack3r2k:.
08-08-2005, 20:37
Hehe :)
Nice to see my old thread is still allive...
byteforce: Yes, this works with every phone, even with Nokia...
Even with yor TV-set, if it has the names pins somewhere...
But, perhapes you should carefully read it. The meaning is: "You cannot see the error message anymore" :cool:
And like schiavo mentioned: TNT will also work very good.
Greetings to all who know me :)
Chris
I'll be damn...look whos here. Never thought will see u arround:D
Br;)