PDA

View Full Version : T610 reboot after 15 sec

gorbulas
10-17-2003, 14:34
Hi all,

i have some problems with a T610 that reboots every 15 seconds. One of our customers have tried to unlock and upgrade the phone with Flashing_Gold 4.?? (sonyericssonserver.com) and after that, the phone reboots every 15 seconds.

I have tried to flash the phone with DIV, but i always get an error 0101

Div says: Bypass boot authority and after 2% the error 0101 appears.

Any Idea what i can do???

DIV works fine with all other phones :-)

br

Markus
jheiner
10-17-2003, 22:54
What version of DIV are you using?
gorbulas
10-18-2003, 10:38
Hi,

iīm using DIV 8.2 , 8.3 and 8.4.


br

Markus
SFlood
10-18-2003, 19:44
0101 after 2% can show what DIV dongle can't turn the phone ON via charging pin after first authorisation try.

Check is the phone accepts charger.
0101 after 2% can't be software problem.
krtko
10-18-2003, 20:36
i has too two phones that stopped bypassing at 2%, both phones was flashed on DIV dongle, one was T68, second T610, i have maked it only with se-fighter and manual ignition.

BR
krtko
gorbulas
10-20-2003, 10:30
@ SFlood

The phone recognizes the charger. Any other Idea? Thankīs for your help anyway :-)


@ krtko

I hope i will get SE-fighter till wednesday (just ordered), what do you mean with manual ignition?


Br

Markus
krtko
10-20-2003, 10:54
@gorbulas, after receiving fighter catch me on icq or mail.

BR
krtko
the_laser
10-20-2003, 12:31
there is easy trick to flash such phones with div.

just do that steps:

1. open back case of phone so battery can be accessible
2. connect div cable to phone
3. start div, select flash files, press flash
4. now the trick ;)
- on t610 without back case we need to press with finger on battery to make contact.
- when div progressbar shows 2% there is small delay before div shows error 0101 or 0102 and during that delay we must release pressure on battery so contact will lost and right after it press on battery again. voila ! progress bar shows 5% ;) we must do such steps until div begin "load data to phone" . then do not release battery until flash is end. and all will be good - phone alive, unlocked and not rebooting.
SFlood
10-20-2003, 13:38
Anyway, this problem related to auto turn-on malfunction.

Another way to try: connect inverted ON signal (after first transistor) to phone ONSRQ/CTS pin 3. Its more reliable way to auto turn-on the phone.
gorbulas
10-23-2003, 18:36
First of all, thanks a lot for reply.


@ the_laser

Thanks for your help.

Trick might be easy, but i guess i am to stupid :( I managed it three times to 80%, but never to the end :D


@ SFlood
Thank you too

I dont want to solder on the PCB as long as i havenīt try SE-Fighter.

I hope i will get SE-Fighter at Saturday and i will give it a try.


Anyway, can any of you two tell me what went wrong with the phone??? Is this a hardwareproblem or just something that went wrong with flashing gold?

I dont think so, because i have sometimes problems with DIV and ARM flashing, DIV stops with an Error at 50%, but i allways can manage to reflash the phone, so any idea?

Other question, how can i reflash a T610 Vodafone with the Vodafone ARM Section (R3C002_EU6-EU7) and where can i get a Vodafone GDFS file?


Thanks

Best regards

Markus
SFlood
10-23-2003, 19:43
I'v heard what SEF can do GDFS backups (real one i think :).
If so, just backup GDFS before unbranding.
Lead
10-23-2003, 19:52
One warning:
Although Fighter creates a 100% correct backup of full T61x/Z60x GDFS, you can't write it to the phone directly using the Flash AVR function.
This is because the GDFS flash chip is not reachable from the original SE flashing applet.
By flashing the file into the phone, you will get overwritten firmware.
If anyone needs to convert such a backup into MDC form, we can do it.
SFlood
10-23-2003, 20:09
what is MDC form?
text-alike block-number-offset-data.gdf ?
gorbulas
10-31-2003, 17:25
Hi,

finally i got my SE-Fighter and managed to fix the phone.

Thanks to all who tried to help.

SE-Fighter is a nice piece of Software!


Best regards


Markus
isaackenny
01-31-2004, 21:34
I had a problem with one pieces of T610 i tried with SEF cant entered boot ... try manual ignition also no success any helped?? I used 2.56b and the phone completely new set .. I just wanna unlocked it..

any help. .
simpa
09-29-2004, 11:33
Hi,

finally i got my SE-Fighter and managed to fix the phone.



Then tell me how did u.
Mine is restarting every 15 secs too, and with DIV i get allways ERROR 3005

@the_laser: any idea about this error msg ?
Uvedovle
09-29-2004, 12:05
One warning:
Although Fighter creates a 100% correct backup of full T61x/Z60x GDFS, you can't write it to the phone directly using the Flash AVR function.
This is because the GDFS flash chip is not reachable from the original SE flashing applet.
By flashing the file into the phone, you will get overwritten firmware.
If anyone needs to convert such a backup into MDC form, we can do it.


I think sould be very usefull if you put in FTP all gdfs in mdc format.

Because when gdfs are damaged the only way to fix this is with The_laserīs tool.


Regards
pchelpsi
10-08-2004, 22:18
I saw you're talking about SE t610. I only need full flash eme2 ( must include Slovenian language ) for the newest - latest version of SE t610 ( the one with rsa ) for divlpt5. If someone has it or know where I can download it, please send the flash ot the link on my e-mail:

pc_help_si@yahoo.com

Thanks in advance for any help.

Br,
Dejan
Uvedovle
10-22-2004, 12:39
Use search, there are many limks arround the forum.

Regards
Siemens man
11-09-2004, 06:13
hi guys
please help me. i'm need tr610 full gdfs. were ican find. tell me url.
thank you
Siemens man
11-11-2004, 21:38
any one help me pleaseeeeeeeeeeeeeeee. need gull gdfs