PDA

View Full Version : cant finish flashing 7650


livewirecebu
01-31-2004, 08:32
am using xp with twister 1.2j and tried flashing 2 units 7650.

Flashing stops after MCU. Then wont flash PPM.

1st Boot Ok, WD2, UPP: 0082
2nd Boot Ok, FLID: 00898876, Intel 28F128W18-T
Algorithm: w2_int_b.fia
Algorithm Ok, MSID: 84321F1EDE89263E7720DC5D6F
Decoded MSID: 3E4EBAF7-009B9C20-A8000000
Encoded FAID: 37D01DD2-F375E071-D1C8607C
Area: 0x00000000-0x0000FFFF Erased, Time: 00:00
Area: 0x00010000-0x00EF9FFF Erased, Time: 02:25
Area: 0x00FF0000-0x00FFC000 Erased, Time: 00:01
BT MCM (26) Image Found & Skipped: 1211
BT MCM (26) Image Found: 22, 0x0002BAC0
BT MCM Flashing Done, Time: 00:12
BT MCM Registering Done
MCU Flashing Completed, Time: 06:52
Erasing: 0x00000000-0x0000FFFF ...
Erasing Error: 10, at: 0x00000000-0x0000FFFF, 9407AA
Process Failed, Repowering Mobile

WojtekXP
01-31-2004, 09:06
Hi,

Check Cablecontacts,
Check the Servicecable,
Change workingspeed to Slow or X-Slow
and try Again...

BR Wojtek

cavite_devil
01-31-2004, 09:41
Bro Paki check yun pc configuration somtimes conflict sa mother driver

livewirecebu
01-31-2004, 11:37
twister works good with other units. just upgraded 2 pcs 3650 to 4.13 today.

cable is also good because i use same cable to flash it with other flashers.

so.. it is not
1) cable contacts
2) service cable
3) usb driver

i havent tried setting on the speed because i have made it back to life with other flasher.

What is the speed all about? when do u need to adjust them?

mali_kruno
01-31-2004, 20:35
What is the speed all about? when do u need to adjust them?
Slow is allway better than fast if you have problems with this phone.
You know how it is if you make something slow that you will not make some errors like with fast method.

Regards Mali

jusluke
02-03-2004, 16:37
am using xp with twister 1.2j and tried flashing 2 units 7650.

Flashing stops after MCU. Then wont flash PPM.

1st Boot Ok, WD2, UPP: 0082
2nd Boot Ok, FLID: 00898876, Intel 28F128W18-T
Algorithm: w2_int_b.fia
Algorithm Ok, MSID: 84321F1EDE89263E7720DC5D6F
Decoded MSID: 3E4EBAF7-009B9C20-A8000000
Encoded FAID: 37D01DD2-F375E071-D1C8607C
Area: 0x00000000-0x0000FFFF Erased, Time: 00:00
Area: 0x00010000-0x00EF9FFF Erased, Time: 02:25
Area: 0x00FF0000-0x00FFC000 Erased, Time: 00:01
BT MCM (26) Image Found & Skipped: 1211
BT MCM (26) Image Found: 22, 0x0002BAC0
BT MCM Flashing Done, Time: 00:12
BT MCM Registering Done
MCU Flashing Completed, Time: 06:52
Erasing: 0x00000000-0x0000FFFF ...
Erasing Error: 10, at: 0x00000000-0x0000FFFF, 9407AA
Process Failed, Repowering Mobile

Bro try mo uncheck autodetct product, uncheck enable BT flash
seems its a BLUETOOTH flash error. Skip BT flashing first then after flashing (check HW version 6018 for new BT config lower means OLD BT, then flash again.