View Full Version : To all unlockers (MC60)
Few days a go I got 10 MC60 sw 10. I cut the same pcb layout like on C60. The phone unlock with Freia 10 was successful, but, keypad YES wasn't working. Later I found out that the layout for YES keypad is nereby the layout for testpoint cut. I solve the problem very easy. Take look a picture. I hope that no one will have this problem.
GORAN_CRO
05-02-2004, 13:06
Few days a go I got 10 MC60 sw 10. I cut the same pcb layout like on C60. The phone unlock with Freia 10 was successful, but, keypad YES wasn't working. Later I found out that the layout for YES keypad is nereby the layout for testpoint cut. I solve the problem very easy. Take look a picture. I hope that no one will have this problem.
vhere is piture ?................................................. ........................
Few days a go I got 10 MC60 sw 10. I cut the same pcb layout like on C60. The phone unlock with Freia 10 was successful, but, keypad YES wasn't working. Later I found out that the layout for YES keypad is nereby the layout for testpoint cut. I solve the problem very easy. Take look a picture. I hope that no one will have this problem.
No picture yet??
Regards
still waiting for the picture to be uploaded
thanks and good work.
eeprom_flash
05-02-2004, 16:22
where is the picture man or u need solution, then creating attention?
BadUnlockers
05-02-2004, 20:27
Guy I See u are new in this forum, if u have anything to show u better show it and stop pulling ppls attention.
Br
DIdi
SORRY FOR WAITING to all of You. When i made this post I forgot to upload picture and I wasnt able to participate in forum few days.
SORRY again
heheheh :D thanx ... it is nice solution ... I will try it :)
This is a 100% solution. Only thing that is important is to use very thin wire. I use isolated wire from coils that are used in old radio receivers. You should cut the rubber on the key Yes too, about one milimeter, becouse when You solder a wire the "click" sound is diferent. I hope that someone will find diferent place on PCB where this track can be shortcircuit, so the customers won't be able to determine any differences :)
Few days a go I got 10 MC60 sw 10. I cut the same pcb layout like on C60. The phone unlock with Freia 10 was successful, but, keypad YES wasn't working. Later I found out that the layout for YES keypad is nereby the layout for testpoint cut. I solve the problem very easy. Take look a picture. I hope that no one will have this problem.
my mc60 scrow,menu and confirm keys are not working can i use this sollution to repair this problem?
br
jeanfleur
09-08-2005, 14:54
Why do you cut MC60?
I use Java
BR,
Jeanfleur
Why do you cut MC60?
I use Java
BR,
Jeanfleur
Not working at vers. 13
my mc60 scrow,menu and confirm keys are not working can i use this sollution to repair this problem?
br
Probable yes! Just try it!
babaunlocker
10-07-2005, 23:11
Guy I See u are new in this forum, if u have anything to show u better show it and stop pulling ppls attention.
Br
DIdi
I Need Help My MC60 just flashing the screen and off after the flashing, what i do?
PLZ Help
WBR
Software problem!
Damaged EEPROM, Wron IMEI, Damage Firmware, broken RamIC....
Just search the board and you will find how to solve it!
babaunlocker
10-08-2005, 21:20
Software problem!
Damaged EEPROM, Wron IMEI, Damage Firmware, broken RamIC....
Just search the board and you will find how to solve it!
It is Ok, When I just reflash it.
Thanks for cooperation