View Full Version : Big Problem Phone Is Dead!!
nicofaase
08-14-2004, 16:08
Hello I've read al posts but I can't still find a answer. Yesterday I tried to update my firmware but my pc shuts down and now won't my phone react on anything that I do... The screen is blank all the time. The option to send it back to Siemens is not possible because I already had upgrade is illigaly to the Benelux version. This is what I've done: I've bought already a serial cable and I've the USB cable. I've tryed to open Winswup 3.05 and select only egold but when WinSwup says connect to box I press ok, and push the red button on my SX1 --> WinSwup says that it connot connect to BootStrapLoader. Or it says other things.... What have I done wrong?
PLEAZZZ HELP
my email is nico.faase@wolmail.nl
ProfiTel
08-16-2004, 20:26
just flash the phone using test point!
how far did the update go when pc went down?
nicofaase
08-17-2004, 12:15
it stocks at 9%.... What is a testpoint? I only have the serial and USB cable to connect to the siemens. Could you please explain how I must do it????
thx in advance
greeetzzz Nico
dima555k
08-20-2004, 12:42
it stocks at 9%.... What is a testpoint? I only have the serial and USB cable to connect to the siemens. Could you please explain how I must do it????
thx in advance
greeetzzz Nico
The best variant for you is vaiting for new version of Martech, testpoint can't halp you, Just try to flash it serial cable with 115200 kbps. Or try to use Freia.
Good Luck.
ProfiTel
08-22-2004, 16:45
you must use test point if you want to flash your phone!
remove resistor,conect phone via serial or usb,use freia or Martech and upload flash file to your phone!
hope it will do some jobe,hope you don`t have sx new pcb...
Wbr
Deki ProfiTel
hitibiti
08-26-2004, 12:25
and for unlock we do same thing ?
remouve thois resistor ?
:)
and for unlock we do same thing ?
remouve thois resistor ?
:)
Yes, for unlock do the same!
But you only need to ground the resistor.
is it nessesery to put again this rezistor after unlock ?
phone work well without it
Normaly you only need to ground it!
But I don't think so! My SL55 is working too without resistor.
jeanfleur
10-28-2004, 21:20
Yes, for unlock do the same!
But you only need to ground the resistor.
On which side is the resistor, battery side?
How do you put off the iron cover that nice that you can put on again?
Because when it is on battery side, client can see it if it is damaged.
BR,
Jeanfleur
The best variant for you is vaiting for new version of Martech, testpoint can't halp you, Just try to flash it serial cable with 115200 kbps. Or try to use Freia.
Good Luck.
plz help me how i flash the SX1. i have freia15 and i have a full flash so help me manuel for flashing. full flash 2 Mb or full flash 8 Mb
battery ?? bootcore ?? eeprom??
think you
gsm-decode
11-16-2004, 17:14
help me
I have a Sx1 and i did full flash on it
Write eeprom
Unlock it with original imei
and the same bzzzzzz thing
i did repair with SST soft but the same
What can i do?
Regards
if your phone dead on software update with usb cable
1- use friea and full flash it
phone will be contact retailer
2- use winswup software then phone will be ok ...