View Full Version : C62 flashing problem :(
DeDaMrAz
09-08-2004, 01:18
:mad: after flash update I get this message
Uploading flash algorithm...
Waiting phone restart...
Uploading flash algorithm...
Flashing failed. Starting flashing failed (algorithm header not valid). Please try recovery flash.
Ok I`ll try recovery flash but then
Initializing...
Uploading flash algorithm...
Waiting phone restart...
Uploading flash algorithm...
Loading software file...
Software file 'HD0503.SEC' loaded.
Flashing software...
Flashing software failed. Block verification failed for block 3, error code: 7.
Has anibody had this type of problem??? Any solutions??? :mad:
P.S. I hate SE CLONES!!!!!!! :mad: :mad:
you need more power for flashing!
DeDaMrAz
09-08-2004, 10:16
:mad: Isn`t 12V enought?!? I flashed 9 pcs. but this one is dead, they all were V16 before, I updated them to v20 and nothing is wrong with other 8 phones. :mad:
How to fix this problem?
Use 12,5v for flashing it's will by O.K.
You must reflow flash chip with hot air station and all be ok.
Good solution to reflow but dont work everytime. Sometimes You have to change the flash chip. Is there anyone who exactly knows the meaning of this code errors???
Block verification failed for block 1, error code: 6
Block verification failed for block 3, error code: 7
etc
Phone was v16 , with bad IMEI
I uploaded recovery flash OK
then for normal flash I get this error :
Language file 'HD0503-LNG-067-M-01.SSW' loaded.
Loading customization file...
Customization file 'HD0503-FFS-067-M-151.SSW' loaded.
Flashing software (HD0503-067-001-M.ssw)...
Flashing software failed. Block verification failed for block 1, error code: 6.
i have the solution for flashing with error code 6 on block 1.
Contact me to solution
i have the solution for flashing with error code 6 on block 1.
Contact me to solution
And that one cost me ?? USD?
Hey Szabyyn, why don't You post the solution (if it is free for You). Or, just say if it is software or hardware problem.
The solution is free & here.
1. to pin9 connect just 9 V.
2.Modification on Flasher Programmer.
- modify the settings on program, to comunicate with the lowest bitrate.
-who has u the program installed it is in CONF directory a HD0503.ini file, edit it and change "Flash Write Mode" wich is 4 to 1.
Thats all.
I hope that help , and u can bring alive the phone after flashing.
Post results pls.(by me work 100%)
Really this is good solution Szabyyn
Some time tis errors comes becaus of cable is bad
If after this solution resive same errors
he must change the cable
DeDaMrAz
09-10-2004, 21:55
The solution is free & here.
1. to pin9 connect just 9 V.
2.Modification on Flasher Programmer.
- modify the settings on program, to comunicate with the lowest bitrate.
-who has u the program installed it is in CONF directory a HD0503.ini file, edit it and change "Flash Write Mode" wich is 4 to 1.
Thats all.
I hope that help , and u can bring alive the phone after flashing.
Post results pls.(by me work 100%)
I will try it first thing in the morning ;) thanks for advice! ;)
DeDaMrAz
09-11-2004, 16:57
The solution is free & here.
1. to pin9 connect just 9 V.
2.Modification on Flasher Programmer.
- modify the settings on program, to comunicate with the lowest bitrate.
-who has u the program installed it is in CONF directory a HD0503.ini file, edit it and change "Flash Write Mode" wich is 4 to 1.
Thats all.
I hope that help , and u can bring alive the phone after flashing.
Post results pls.(by me work 100%)
It didn`t work :( :(
Hello! I change 4 to 3 and all works! But with one unit i have same problem.
This is not 100% solution, thats for sure:(
thanks scotch!!!
working now!!
bentys2000
10-07-2004, 11:48
please scotch how do you change 4 to 3.... be specific
mobiletools
10-09-2004, 18:49
TRY TO CHANGE 4 to 3 and PUT 12v to pin 9 it works 1000000000%
Has anibody had this type of problem??? Any solutions??? :mad:
P.S. I hate SE CLONES!!!!!!! :mad: :mad:
Make sure you have 9-12v at pin9.
Most problems are going from that.
why when i try to flash it said that my cellphone version need higher version of flasher software????
mobiletools
10-12-2004, 22:34
no pb with 12v i tested in many phones
Hello! I change 4 to 3 and all works! But with one unit i have same problem.
I fix this problem! I flash all phones, submitting on 9 pin 5 volt, but some phones are not flashing, the program gives out a mistake: Block verification failed for block 1, error code: 6. Then I submit on 9 pin 9 volt and phone are normally flashed. Probably, some flash chips demand the greater pressure of a feed.
Sorry for my bad english! :p
i have try f;ash my c62.....it "success"...
BUT yhe phone now "HANG"....no response...just blank
any idea????
do i have to change flash chip????
change 4 to 3?????
anyone know the meaning???
vladutstoian
11-13-2004, 13:16
I had some problem but I reflash my siemens c 62 good work and thanks for all help
and which pins are correct for TX and RX for flashing C62? I have same problem. I used pin 7 for TX and pin 5 for RX. It seems i can flash the phone, but i can't read information. Then i used other pins, (3,4) i was able to read info, but couldn't flash phone. Please, i need advice...
I tryed to connect pin 3 with pin 5 and pin 4 with pin 7... I still get same errors:
Flashing software failed. Block verification failed for block 1, error code: 6
and which pins are correct for TX and RX for flashing C62? I have same problem. I used pin 7 for TX and pin 5 for RX. It seems i can flash the phone, but i can't read information. Then i used other pins, (3,4) i was able to read info, but couldn't flash phone. Please, i need advice...
I tryed to connect pin 3 with pin 5 and pin 4 with pin 7... I still get same errors:
Flashing software failed. Block verification failed for block 1, error code: 6
Here's a tested pinout to flash and revive dead C62
-Pin 2 =Gnd
-Pin 3 & 5 are connected to TX
-Pin 4 & 7 are Connected to RX
-Pin 9 is connect to a External +9V DC , of course the External GND is grounded with Pin 2 !
Use Flasprogrammer 2.83 , Edit the HD0503.Ini file , change flash mode from 4 to 3
hightechsquare
11-30-2004, 14:41
i have founfd the solution of the error
hightechsquare
12-06-2004, 13:42
ok use the win98 and change teh ini file from 4 to 2 it's so easy
hi, who can help me with prob,
i have c62 work fine , with Baltic lang pack an international cust pack, one day i revived this phone using a cable that i maked (cable with 12v external power),
but to day i decided to change the lang pack to midle east or international, i do everything (pL driver, flash programer and software relise 083).
now when i power on the phone and click (show information) it work and show evry thing . copy user data too it work fine, but when i click flash here is what hapen:
*********
Initializing...
Uploading flash algorithm...
Waiting phone restart...
Uploading flash algorithm...
Flashing failed. The phone is not responding to load header command.
*********
i tryed flasher 2.71 - 2.78 -2.83 and changing power external from 9v-10v ..... 13v , the problem is the same.
Hello All C62 Imei Corrupted Any Way 2 Solved It?phone Locked..regards