rotorman
09-13-2004, 02:15
Some of you might have already tried these but if not, here is a list of codes and what they do when fone is in manual diag mode from pressing 0,3,right-soft,power then 0,1,2,3,rt-soft,1
Code Result
04 Mon Signal
05 Measurement
07 Sim Check
08 Country Setting
13 IRDA Test
14 NVRAM Area copy
28 IMEI Code Can enter 4 digits but don't know how to save them.
The firmware does have msg Now Setting IMEI.Don't know how to
get it tho and input seems to be in hex.
30 UART Test
33 Camera Control
34 Exposure
35 Ca Balance
36 Wh Balance
38 CPU Clock
39 Ip Image Control
40 RTC Setting
42 Temp Adj
44 Batt Control
45 LED Setting Note fone appears to turn off but it’s only LEDs
off. Press 4 to turn on main scrn. Each press of 4 alters brightness.
Other keys press once to turn LED on, again to turn off.
47 Lpf Change
48 Wh Balance
51 Melody Test Lft Soft-IC Power Rt Soft-Key Touch 1-Sin Wave
UP/DWN-Volume LFT/RT-Melody Number 0-Play
52 Audio Setting
54 Codec Loop
66 Assert Fail Log Performs Diag Parm Save
72 AFC Setting
73 Flash Check
74 RF Setting
77 Power Control Perhaps usefull for measuring voltages at these
points to check cct operation
80 Voltage Control
81 LCD Setting When 9 use UP/DWN
82 Image Receive
83 SRAM Checking Press 1 to set TOP range RtSoft to save. 2 sets
END range. 0 starts test.
85 Sub LCD 8-pattern 7-on/off Unsure how to exit
87 Camera Prm Init Possibly initialises settings made earlier. 1-6 or 0
for all
93 Memory Read Address 8/16/32bit
96 LCD Prm Init
97 Key Ageing Test (yeah my keys are gettin old man LOL)
98 E2 Emulation
99 Following modes are…
01 Format and Reset
02 SIM Flag ON/OFF
03 Genie Flag ON/OFF
This is all I know about these things. Any Q's like 'What does this do' or 'How do you do this..' will be ignored.
Have fun!
JD
Code Result
04 Mon Signal
05 Measurement
07 Sim Check
08 Country Setting
13 IRDA Test
14 NVRAM Area copy
28 IMEI Code Can enter 4 digits but don't know how to save them.
The firmware does have msg Now Setting IMEI.Don't know how to
get it tho and input seems to be in hex.
30 UART Test
33 Camera Control
34 Exposure
35 Ca Balance
36 Wh Balance
38 CPU Clock
39 Ip Image Control
40 RTC Setting
42 Temp Adj
44 Batt Control
45 LED Setting Note fone appears to turn off but it’s only LEDs
off. Press 4 to turn on main scrn. Each press of 4 alters brightness.
Other keys press once to turn LED on, again to turn off.
47 Lpf Change
48 Wh Balance
51 Melody Test Lft Soft-IC Power Rt Soft-Key Touch 1-Sin Wave
UP/DWN-Volume LFT/RT-Melody Number 0-Play
52 Audio Setting
54 Codec Loop
66 Assert Fail Log Performs Diag Parm Save
72 AFC Setting
73 Flash Check
74 RF Setting
77 Power Control Perhaps usefull for measuring voltages at these
points to check cct operation
80 Voltage Control
81 LCD Setting When 9 use UP/DWN
82 Image Receive
83 SRAM Checking Press 1 to set TOP range RtSoft to save. 2 sets
END range. 0 starts test.
85 Sub LCD 8-pattern 7-on/off Unsure how to exit
87 Camera Prm Init Possibly initialises settings made earlier. 1-6 or 0
for all
93 Memory Read Address 8/16/32bit
96 LCD Prm Init
97 Key Ageing Test (yeah my keys are gettin old man LOL)
98 E2 Emulation
99 Following modes are…
01 Format and Reset
02 SIM Flag ON/OFF
03 Genie Flag ON/OFF
This is all I know about these things. Any Q's like 'What does this do' or 'How do you do this..' will be ignored.
Have fun!
JD