T610 stops at 2%

[ricson]

tried to flash phone using DIV but always stops at 2% bypass bootloader

what could be the problem

[thetunisiancrow]

same problem as me so please (sorry i was write twice)

[thetunisiancrow]

same problem as me and my phone is dead

[andrew2304]

Guys, use TP and Div, or wister RTP v2.6? Read here:http://forum.gsmhosting.com/vbb/showthread.php?t=159342
BR.

[thetunisiancrow]

i diddn't find me any thing in this topic so plesase explain more and what is wister RTP v2.6
thanks

[magnet]

mr.andrew2304 is saying about test point(tp).
if your mobile is rsa protected.you must use div5.0 or twister rtp 2.6 versions.

i think your mobile is showing error 0101.
if this is the error let me know, i can help u to some extent (as per my knowledge)

[thetunisiancrow]

no my error is 01a1 so who can explain me this

[ricson]

I got error 0101 can u help me

The reason why i want to flash the phone is whenever i take a picture it always hangs.

Firmware version is not R6C

Tried flashing with UFS3 also no luck same result for DIV.

Is it a hardware problem.

[magnet]

is it stopping at 2 %.
or no progresss .

error 0101
means not communicating.

[magnet]

Solution for error 0101 with no 2%

- Clean your contacts
- Cable may be faulty
- Wrong settings for LPT port
- Battery not loaded

[magnet]

solution for error 0101 with 2%

1. open back case of phone so battery can be accessible
2. connect div cable to phone
3. start div, select flash files, press flash
4. now the trick
- on t610 without back case we need to press with finger on battery to make contact.
- when div progressbar shows 2% there is small delay before div shows error 0101 or 0102 and during that delay we must release pressure on battery so contact will lost and right after it press on battery again. voila ! progress bar shows 5% we must do such steps until div begin "load data to phone" . then do not release battery until flash is end. and all will be good - phone alive, unlocked and not rebooting. "

Well, i tried this steps fif**** or twenty times until it worked, you have to be a lot of patience but finally works.

[ricson]

Tried your procedure it works but stops at 35% will try again hope i can be succesful like u .

Thanks

[hightechsquare]

to lall member who have this problem and like my friend houssem "thetunisiancrow"
i will give u the solution step by step contact me in icq
last sunday i have get this and i have repair 3 phone with this fault exept the phone of
thetunisiancrow when i have used the div usb 5.0 i have get many problem ( i have unlocked about 123 phone so if u want any think me and a ll my staff will help u and thanks to the _laser )

[ricson]

can u PM me the soultion sorry dont have icq

hope to hear from u soon

[soybean]

I have experience this 2% problem and fix it by bending the connection between dongle and cable, because the connection between dongle and cable is loose.

good luck

[wabou]

for myself
i solve the problem by this way

1 changing configuration of the ltp port ,i do ecp +epp
2 flashing the t610 with div 8.2 cracked with a new fully charged battery

i flash arm + avr r6b004 eu5

and all is ok

i think that in fact the problem is the battery it must be FULLY CHARGED
:D :D :) :) :D :D

[Dafageni]

I have unlocked 6 or 7 phones where the process bar stops 2% just by pressing on the the ON button everytime until you see the process bar go automatically. As you press the on button will see on the process bar that it climbs from 2 to 5 to 7 to 10 everytime plus 2 and them plus 3. This is not a difficult way to unlock the phone. Just don't press the ON button to long. In this case the phone WILL power on and the unocking process will fail.

[Dafageni]

Please Let me know if you succeeded.

[starchrisson]

what is div cable what can it be use for and how does it work?Help

[akbarbaba]

hi there i have problem.i try to unlock t610 with twister but the phone is dead plzzzzzzz help me