Hardware Repair Series : 7210-6610 no power on after flash [Archive]

GSM Coolhawk

11-10-2004, 10:25

Please see following picture for solution to DCT4 7210 and 6610 no power on after flashing, with no appearent damages to the board, or light waterdamage.

http://www.gsmcoolhawk.com/gsmforum/repairpics/6610_7210.jpg

All credits and thanks for this goes to StuioGSM for posting the picture

Please note that original bmp file of 855 kb was resampled to jpg 51 kb !

Regards

yousha

11-10-2004, 10:30

yes we know it its a track b/w flash and ram if the phone does`nt power on even after this track than replace RAM

anyways thanx GSMCOOLHAWK

Edit by GSM Coolhawk**The thanks goes to StudioGSM for posting picture**

Azampk

11-11-2004, 00:19

ya it's work for me in water damage set 6610

but still no network pls help me i reflashed but nothing and no lights

Edit By GSM Coolhawk

@azampk

Please take care. Stay within topic, this is for no power on when phone can be flashed. Make a new thread or search the bord, there's litterally over 40 posts containing your question regarding signal.

StudioGSM

11-11-2004, 21:42

this is really great . working solution, thanx to StudioGSM

thanx again

@kki
OK. No problem friends. It's good to see some good words for me. :cool: Next solutions will be ready soon.

BR
StudioGSM.pl

baraka42

11-12-2004, 08:35

this solution can work with 3100, same problem ?

w.b.r.

yousha

11-12-2004, 08:50

this solution can work with 3100, same problem ?

w.b.r.

no my frnd the platform is totally differs

baraka42

11-12-2004, 09:16

yes yousa,

u right, i hadn't refer 3100 sche. there is combo memory.

in 6610 c451-c452 is memory coupling capacitor for ram.

w.b.r.

pali

11-16-2004, 10:48

this solution is not working for me :
when i connect this 2 capacitors then i cant flash my phone .
see here :

9B0201008C2290000000800200000000...
Failed to find FIA file in 'C:\Program Files\Nokia\Phoenix\flash\
In 994314770f the cases this is caused by corrupt FLASH folder.
Fully DELETE the contents of the Flash folder,
and then Install the latest FIA package!
Error[78878778]
bad ID of Flash ic .
without this bridge i can flash my phone but dont power on after flashing .

see here :
Initializing Phone...
Flash configuration:
9B020100EC22F2000000E00200000000...
Boot and Flash loaders operation took 5.128000 seconds
Erasing ....
etc..
there is different FLASH ID .
any idea ?

Pali

akshay

11-16-2004, 16:04

then try to make jumper btw capecitors . or try to on phone. if not then rehot ram
or change ram, or sometimes uem also reason for this type of falult.

@kki

pali

11-17-2004, 18:08

@akshay
well
Ram is changed , all BGA reballed , board doesnt seems to be damaged.
if i connect this 2 Capacitors then i have error .
If i dont connect i can flash my phone , flash id is correct.

any idea?
what about other Capacitors near RAM and FLASH IC ?

Pali

NELU-GSM

11-23-2004, 09:05

I MAKE CONNECTION LIKE IN PICTURE,PHONE POWER ON 3-4 TIMES AND NOW ONLY WHEN I MAKE WITH TORNADO REBOOT IN NORMAL MODE PHONE IS POWER ON .WHAT IS THE PROBLEM? :confused:

needi

11-26-2004, 02:07

Bad Ram...try with new RAM.

baraka42

11-26-2004, 08:03

thanks m8,

with your solution i can power on 6610, with c.s. imei is ?????????????

phone can power on with twister normal mode for few second.

need more help.

thanks again.

w.b.r.

badi

12-01-2004, 23:02

Bad Ram...try with new RAM.
yes m8 this is the right solution to fix this prob ;)

mrfixit

12-12-2004, 19:27

this extra wire connection worked for me too

maliknawa

12-12-2004, 23:36

Pls To All Ihave Mor Than 1 With This Pb I Realy Need Help To Solv This Pb And Save My Mony .i ,d Try All This Slo But No New My Phone Is Still Flash But Not Power On
And Thanx Forall

flechazo

12-13-2004, 00:55

Test And Work Fine

ReGards ... SuDDa 1m²:D

maliknawa

12-13-2004, 01:36

i say iws do all of sol but dsnt respons
if u hvnt *** id dosnt say tes and wor fine ineed to new solo
but thankx alot to u for post mr flechazo

maliknawa

12-15-2004, 01:49

Iam Wating To One Who Can Help Me
Whom????

Nokall

12-20-2004, 18:53

can you make this solucion to work on 6100 no pwer after flash :( thanks
b.r

lpsorcerer

12-20-2004, 19:31

yes i need too :(, please for who knows...

pali

01-01-2005, 22:28

for me not working, maybe other problem .
i have 6610 , not AFP and cant power on .
flashing .. ok except EXTRACTING ...failed.
when i make this connection then i cant flash my phone.
Any idea ??

Pali

shivram

01-23-2005, 05:21

i have 6610 dead,flashed with ufs3 normal mode failed,the two cap connction not working for me,please any help with max,thank for the new connction

pssujesh

01-23-2005, 07:52

check the print fom C450 to C 452 and alos me rectified this complaint by changing RAM

pssujesh

01-23-2005, 07:54

havo u got it? check the RAM also

pali

01-24-2005, 00:29

when i make connection (it is broken) then i cant FLASH my phone !!! any idea why ?

Pali

SR-sigma

01-24-2005, 06:38

HELLO SIR
You given good solution thanks but that track will be OK but after flash NO POWER ON any outher solution i am flash ic and UEM ic also reboll the fault will same

A Z MOBILE

01-29-2005, 03:03

hello plz help me i need nokia 3310 service manual thenx

jokkergsm

02-10-2005, 16:37

worked 4 me too ...

but i have one 6100 with the same symptoms...

is there any other option similar to this one??

pali

02-12-2005, 22:03

[QUOTE=pali]this solution is not working for me :
when i connect this 2 capacitors then i cant flash my phone .
see here :

9B0201008C2290000000800200000000...
Failed to find FIA file in 'C:\Program Files\Nokia\Phoenix\flash\
In 994314770f the cases this is caused by corrupt FLASH folder.
Fully DELETE the contents of the Flash folder,
and then Install the latest FIA package!
Error[78878778]
bad ID of Flash ic .
without this bridge i can flash my phone but dont power on after flashing .

see here :
Initializing Phone...
Flash configuration:
9B020100EC22F2000000E00200000000...
Boot and Flash loaders operation took 5.128000 seconds
Erasing ....
etc..
there is different FLASH ID .
any idea ?

well, im working on it again.
i checked link from C451 to C452,C450,C207,C404 all are ok.
i must repair just C451-C452... (if link is made i hade bad FLASH ID, phone cant be flashed)
If i dont repair this link , i can flash my phone but cant power on ..
any idea?
what to do next.
Ram ic is changed.

Pali

yoya

02-18-2005, 22:48

Change flash ic, if use combo flash ic like on 7250, 3200 remuve ram ic.
Best regards

juht

02-25-2005, 11:46

to be continued to be continued
This picture, last, is wrong!!!! The wire must be in other pin of the same capacitor!!!!

Spacewalker

02-25-2005, 16:49

picture is good - becouse I repair some 6610 and this cross help this ;)
and - have this some problem with 6230. Remove second (small) flash - not help. remowe UM - not help

Initializing Phone...
Flash configuration:
9B0400EC00F8220000110002FFFFFFFF...
Boot and Flash loaders operation took 5.818000 seconds
Erasing - erase took 114.721005 seconds
Flashing MCU - flashing took 132.783006 seconds
Flash configuration:
9B0400EC00F8220000110002FFFFFFFF...
Erasing - erase took 16.256001 seconds
Flashing PPM - flashing took 29.231001 seconds
Flashing DONE
After flash processing...
Trying autopower
Fail

use erase file - not help this problem.

jokkergsm

02-25-2005, 17:01

yes picture is ok...

i repaired 1 phone too using this solution...

REGARDS

juht

02-25-2005, 17:29

Red line is OK, but the black line to C207 is wrong - goes to ground and UEM is warming up :D
It must be right the blue line

mohd_anan

02-27-2005, 13:19

Working 100%

Tested

Thnks for sharing

RedBaron
KUWAIT

flechazo

02-27-2005, 15:13

Work With 2 Phones Thx STUDIO GSM

ReGards .. SuDDa 1m²:D

pali

02-27-2005, 22:53

what about this picture?

check it please

pali

jokkergsm

02-28-2005, 17:01

what about this picture?

check it please

pali

-------------------------------------------

yes!!!!

that`s the best solution ever!!!

but .... u MUST use the same colours on wires ...otherwise it won`t work !!!

:D

Beyond Matrix

03-02-2005, 18:05

i come across n-cage can flash but griffin cannot power up after flashed.

any solution for n-cage?

cheers

jokkergsm

03-02-2005, 22:56

i come across n-cage can flash but griffin cannot power up after flashed.

any solution for n-cage?

-------------------------------------------------------

try with twister ..i had that problem too ...and with twister my phone powered on ....

in your case it may not be hardware problem...

REGARDS

excelpass

03-07-2005, 11:18

6610 water set after hanging ic n flash ok but now no buzzer sound, any idea or diagram to help?10x i advance

juht

03-07-2005, 15:35

No buzzer means, that you must reball or change a little amplifier for speaker. See the picture.

sonia_321

03-07-2005, 15:55

Hi,

I have strange 6610. Phone is water-demaged. In board used K8S64158TM, but Tornado says K5U64418TM! I changed IC flash, SRAM IC, UPP, UEM, HELGO. I cleaned the board. But the problem persist!
I use Tornado v.1.3i. In previous versions Tornado is the same. After flashing the phone blinks for 2s. Conections to C450, 451, 452 etc. is OK.
Does anyone knows where is the problem????

dipakgt9

03-07-2005, 16:00

thanx for this needed solution. can some help me to repair n6600 no display after tryed to repair lcd leds now leds are ok but no display.

dipakgt9

03-07-2005, 16:42

finally i solved my problem with replacing display conector

excelpass

03-08-2005, 06:30

i have change but still no ringtone

juht

03-08-2005, 08:18

i have change but still no ringtone

Are you 100% sure, that buzzer itself is ok and tracks also? I think you need a service manual to chech all tracks also.

c0c0

03-09-2005, 16:21

and how about 7250 i have one same problem.......

flash but no power on it was droped!!!!

windelas

03-18-2005, 20:53

and how about 7250 i have one same problem.......

flash but no power on it was droped!!!!
try to change the crystal clock or flash ic :cool:

windelas

03-18-2005, 20:59

Bad Ram...try with new RAM.
:cool: try to check the connection of a3 of ram. :cool: A3 is supply for ram ic
:cool:

gsmphone

03-30-2005, 13:10

I have a Nokia 6610 and it fell on the ground. What should I do because it doesnt want to turn on. Please help me. Thanks

amitks_in

04-11-2005, 15:45

can anyone tell me Nokia 2600 Lcd is compatible with any other Nokia phone ? oris it same as 6610 nokia ?

amitks_in

04-11-2005, 16:15

-------------------------------------------

yes!!!!

that`s the best solution ever!!!

but .... u MUST use the same colours on wires ...otherwise it won`t work !!!

:D

You said same colours of wires. but colour coated wires are very heavy, I mean wires like in data cables, should I have to use the cables same as data cables made from ? will they be able to perform a circuit ? thease type of colour coated wires are very heavy

shailesh_chauha

04-12-2005, 12:19

Thanks For Solution I Like To Know More About This Fault

gsmsikar

04-19-2005, 22:15

hi

is there any solution like this for the same problem in 3100/3120 ?

help

CellWorm

05-21-2005, 21:25

flash phone in slow or x slow speed phone must power on.

amitks_in

05-22-2005, 13:31

I have 6100 with flashing ok but cant power on ! can u plz give me the solution

tan2x81

05-23-2005, 06:24

try using another flash file.. maybe there is something wrong with your flash file.. coz i have experienced it before... :D

CellWorm

05-23-2005, 17:19

flash phone with new ver. firmware

CPUKILLER

05-23-2005, 22:08

I have 6100 with flashing ok but cant power on ! can u plz give me the solution
if its a fallen or water logged or tempered phone then pickup the upp chip and below uwill see broken or corroded points try cleaning and reballing if this is notthe case i.e. if its a clean board then its the firmware problem thats it for now check and post results

Alpha2000

06-01-2005, 21:30

Cek BSI line, 32 Khz Clock at testing point nar CPU (J104), UPP

PHONESTREET LIMITED

06-27-2005, 17:21

Hi moderator i love this solution thanks alot
and greetings to all brothers in the forum
Good luck 4 the day

GamalyGsM

06-27-2005, 19:24

iam tested it ... and its doesn't work with me :(

davidmichael

08-11-2005, 02:35

babaunlocker

09-07-2005, 22:47

Service MEnual is not sufficient for track tracing, becoz when track goes into the 2nd and 3rd layer which are both in inner side of PCB, than what is your tracing method, my 90% problims will be ok if you tell me about the tracing of inner link connection joints.

Waiting for your reply

raj_bhatia66

10-07-2005, 13:29

use erase flash first then flash mcu,ppm one by one.after flash go for format user area:D

Alpha2000

10-13-2005, 22:00

can anyone help me...
i have m/fbus serial cable for my dct3 phone, i tried to use it for my n3100, connected fbus tx, fbus rx and gnd on the terminals... but it wont work... i thought doing it wud make it possible to use MobiMB with it. Is it really possible to use it or shud i use a different cable? i want to upload and download games and pictures there... pls help me... THANX IN ADVANCE!!!!!!

just use DKU-5 cable for N3100 will be work. but it's possible to use fbus cable for N3100. maybe ur dct3 cable is not pure fbus. it's automatic fbus/mbus dct3 cable. it can't be used.

and how u connect the cable to ur n3100? u solder the wire, to the bottom pcb or near sim card?

TURNING POINT

10-14-2005, 12:30

-------------------------------------------

yes!!!!

that`s the best solution ever!!!

but .... u MUST use the same colours on wires ...otherwise it won`t work !!!

:D
would u know what u want to advice ?any way thanks for advice

hiteshsangadia

10-23-2005, 14:58

hi i have tryed this and it worked for me for 6610........
thanks for yr support

albert maren

11-16-2005, 15:43

7210 i conect the wire did not power and when i put my tornado cable to try flash it will not conect but the keypat led will show.pls what will i do.

tedjo13

11-22-2005, 23:46

Change flash ic, if use combo flash ic like on 7250, 3200 remuve ram ic.
Best regards

Anyone ever try this??
Please confirm...

jarniel

11-30-2005, 20:31

i have change but still no ringtone

chnge the upp with new 1,reflash then unlock. after this check the phone with sim....

marvintawanda

02-27-2006, 19:25

i hve 6100 was no rinng no keypads xcpt 369 , did keypads and ring bat now batt low everytime i switch on even with 110% batt power. pliz elp

phonetech_tz

04-04-2006, 09:27

hi , my friend ,
my 6260 is not switch on after flshing software,it already reballing is done in flash ic.pls any body having 6260 picture pls send me.

and advice me for this problem

phonetech_tz

04-04-2006, 09:39

if its a fallen or water logged or tempered phone then pickup the upp chip and below uwill see broken or corroded points try cleaning and reballing if this is notthe case i.e. if its a clean board then its the firmware problem thats it for now check and post results

my nokia 6260 after flashing software ,its not switching ON, i reballing the flash ic..

pradeep agrawal

05-14-2006, 11:19

hi friend please help me for nokia 3220 contact service

yosif_gsm

05-21-2006, 18:22

i,ll tray this but it,s not working with me
what can i,ll do again
i have 6610 not bower on after flash:)

m4m

07-01-2006, 23:03

gooooood solution

it's work

thank you too mutch

etcelfon

09-26-2006, 06:57

ok dude..good job thankds..

sanjay telecom

02-15-2008, 04:14

plz sove my problem any bady
7610 keypad ic jumper
plz send me how can set the keypad jumper
also show picture & attched jumber plzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzz zzzzzzz
helppppppppppppppppppppppppppppppppppppppppppppppp ppppppppppppppppppppppppppppppp