Sagem CDR V 14.0 & myX-1 BAD CONNECTION?

[mfreaks]

Sagem CDR V 14.0 & myX-1 BAD CONNECTION?
Any one else have this issue?

This is really doing my head in, some help or any known issues thatmaybe I should know.

Steps I Do:
Select myX-1
Power on phone
Read code

Then the progress bar goes across quite quick at bottom
then says ERROR: Bad Connetion

Help

[electrohicham]

verify you cable connection and clean conector all you have to do is verify connection ;)

[flechazo]

BAD CONECTION = BAD TEST POINT :D

ReGards .. SuDDa 1m²:D

[mfreaks]

BAD CONECTION = BAD TEST POINT :D

ReGards .. SuDDa 1m²:D

What do you mean?

Also have tried other good cables that I know work.

I thought it was a case of just connecting cable to myx-1
What do you mean about test points on myx-1

[florinfr80]

I had the same problem, i solved very easy.
selected another type of phone in software, so try myx 2- myx3..... etc. One will work, nothing happend don't worry it is only a reader. You have nothing to lose, do as I say. You' ll see....
it will work, believe me

[mfreaks]

I had the same problem, i solved very easy.
selected another type of phone in software, so try myx 2- myx3..... etc. One will work, nothing happend don't worry it is only a reader. You have nothing to lose, do as I say. You' ll see....
it will work, believe me

I tried that already, if I select diffrent model, it just says phone not found.
Could this be a cable Issue, as in dodgy?

Cheers

[florinfr80]

I tried that already, if I select diffrent model, it just says phone not found.
Could this be a cable Issue, as in dodgy?

Cheers
look closer to see if your testpoint are ok. if yes rewrite the atmel inside reader and rehot pcb of the reader.
If this doesn't work you must find out if this the phone or the box

[yeldar]

After pressing DO JOB, try to unplug the data plug from the bottom of handset and plug back in.......I have had a few that do this and the reader then gives code in about 3-4 seconds!!

[ics_igrec_zet]

To find out if is box deffect try to connect 3026 infineon, because u don`t need test point to this model and if phone connects then box is good and u have test point problem (inverted cables or intrerupted tracks).
B R, xyz

[mfreaks]

After pressing DO JOB, try to unplug the data plug from the bottom of handset and plug back in.......I have had a few that do this and the reader then gives code in about 3-4 seconds!!

Done all that believe me have tried all sorts.


To find out if is box deffect try to connect 3026 infineon, because u don`t need test point to this model and if phone connects then box is good and u have test point problem (inverted cables or intrerupted tracks).
B R, xyz
Yep that connects then obviously says error execution:

So is this then a duff, bad dodgy cable?

[mfreaks]

Ok
Just a thought the USB power cable to the box is connected to another pc
would this have any adverse effect?

As im using an old 98se system with no usb, so usb is connected as stated to another machine.

[MAK_US1977]

just downgrade ur dongle to ver 10
it will work
100% tested

[kumkon]

don't forget printer port mode setting to EPP in bios of your PC

[mfreaks]

just downgrade ur dongle to ver 10
it will work
100% tested

So it's not cable issue? but product issue?
Huh

I use 10_12_13
& none of the versions work;
Same error will read then bad connection!

[MAK_US1977]

when i try unlock some models with V14 it say unsuported ver
but with ver 10 all ok

note : MYX3-2 only work with me on ver 14

[MaFiaaa]

downgrad yr box to v12 thats better than 14
here is all u need for yr box : http://repair-electronics.com/MaFiaaa/Sagem/sagem%20cdr%20all.rar

[mfreaks]

downgrad yr box to v12 thats better than 14
here is all u need for yr box : http://repair-electronics.com/MaFiaaa/Sagem/sagem%20cdr%20all.rar

Thats for cloned boxes above link:
No good to me, Like I said I already have choice to use:
10
12
14

None of them Work

[fido]

hi,

change MCU on Dongle

only this help to you


i had the same problem....

regards

fido

[MaFiaaa]

if u have orignal box i think u didn`t get error for that i talk about cloned one

[mfreaks]

Can anyone please advise if this is the Product Fault!
So that at least i can get a solution that works & send it back?

[mfreaks]

Just to update any users:
I have v14 dongle coming which i'm told "works very well and is very stable, but you wont get it to unlock myv-65 and myx-7"

So will see how I get on.

[Spacewalker]

I upgrate my clon SCRD to Oryginal ID and work Good (V14). Make about 15 MyX1 - all work.