!!!!!nec P7 Programming Instructions !!!!!!

[sunnyc]

1.PRESS PWR KEY TO POWER UNIT ON
2.PRESS 9 * 7 6 2 # # 0 7 4 FCN RCL 7 6 RCL # 0 1
3.PRESS RCL # 7 1
4.PRESS # 5050 ( FOR 018 ) OR 5060 ( FOR 015 ) THEN THE LAST 6 DIGITS OF THE MOBILE NUMBER
5.PRESS # THEN THE 4 DIGIT LOCK CODE
6.PRESS # THEN THE HOME AREA SID CODE.
7.PRESS # GI MARK 00 (LEAVE AS IT IS)
8.PRESS # FIRST P-CH 0333 (LEAVE AS IT IS)
9.PRESS # SYSTEM A-1 (LEAVE AS IT IS)
10.PRESS # ACCOLC PUT IN 0 AND THE LAST DIGIT OF THE MOBILE NUMBER
11.PRESS # MIN MARK YES-1 (LEAVE AS IT IS)
12.PRESS # LOCAL USE YES-1 (LEAVE AS IT IS)
13.PRESS # EMG NO 000 (LEAVE AS IT IS)
14.PRESS # FCN STATE 00 (LEAVE AS IT IS)
15.PRESS # 018 * OR 015
16.PRESS # PROGRAMMING IS COMPLETE
17.PRESS CLR FOR 1 SECOND
18.PRESS RCL # 0 2
19.POWER OFF UNIT
20.TO CHECK PROGRAMMING WAS CORRECT POWER ON UNIT
PRESS FCN AND IT WILL SHOW 018 XXXXXX OR 015 XXXXXX

NEC OPERA PROGRAMMING INSTRUCTIONS

1.PRESS O TO POWER UNIT ON.
2.PRESS 9 * 2 5 7 # # 2 7 8 F MR 7 6 MR # 0 l.
3.PRESS MR # 7 l.
4.PRESS # 5050 (FOR 018) OR 5060 (FOR 015 ) OR 5080 (FOR 019) OR 5090 ( FOR 014 ) THEN THE LAST 6 DIGITS OF THE PHONE NUMBER.
5.PRESS # THEN THE 4 DIGIT LOCK CODE.
6.PRESS # THEN THE HOME AREA SID CODE.
7.PRESS # GI MARK 00. (LEAVE AS IT IS)
8.PRESS # FIRST P-CH 0333. (LEAVE AS IT IS)
9.PRESS # SYSTEM A-l. (LEAVE AS IT IS)
10.PRESS # ACCOLC. PUT IN 0 AND THE LAST DIGIT OF THE PHONE NUMBER.
11.PRESS # MIN MARK YES-1. (LEAVE AS IT IS)
12.PRESS # LOCAL USE YES-1. (LEAVE AS IT IS)
13.PRESS # EMG NO 000. (LEAVE AS IT IS)
14.PRESS # FCN STATE 00. (LEAVE AS IT IS)
15.PRESS # 018 * OR 015 * OR 019 * OR 014 *.
16.PRESS # PROGRAMMING IS COMPLETE.
17.PRESS MR # 2 4 TO CHECK ESN. ( THIS STEP IS OPTIONAL )
18.PRESS MR # 0 2.
PRESS F QUICKLY TO REVIEW PHONE NO. PROGRAMMED. PHONE WILL DISPLAY 01X XXXXXX ( THE COMPLETE PHONE NUMBER )
19.POWER OFF UNIT.


--------------------------------------------------------------------------HI i dont no what is this pls tell me ?????????


sunnyc

[krusty.spritz]

wooow a blast from the past.......

this is an analogue mobile fone (etacs) :D
ok if the brain serves me well, you are in the n.a.m. programming menu (number activation module) in the fones eeprom area.

all you can do here is set the mobile number lock code and network parameters, but its useless these days as they wont work in the uk.

if you have the old network runing over there still try this......

after rcl# 01 do this
rcl#12 (open rx path)
rcl#69 (initiate channel scanning)
0000# (enter channel 0000 to 1320....they only have 1320 channels per base station to scan)
then when you here voices from the fone press the * key to hold it on that channel......* starts and stops the scanning function !!! :eek: :eek: :eek:

enjoy....

[gsmdreams]

Where did you guys study from . :-)

[..::COZEC::..]

Where did you guys study from . :-)

They must have studied on the moon. maybe :D

[krusty.spritz]

Where did you guys study from . :-)

there is no school for this stuff :D read..think read......think