need solution for my v55

[GSM SHADOW]

i need any solution for myv55 urgently :confused: :confused: :confused:

[amine gsm maroc]

;) This operation it is not for beginners :D , juniors or rookies!!!!

I will explain step by step. Works 100%

1. You must heat the flash IC of Sagem MyV 55, from 150 to 400 degree for about 10 minutes, but you must rise temperature progressive until you can pull it out from the black resin, or if you a solution which dissolve resin you can use it. At this point be very careful how you can get it out the flash with out destroy it.

2. You must heat and unsolder the flash from a Nokia 3310.

3. In place of Nokia 3310 flash put the Sagem flash that you unsoldered in the first place

4. After you soldered the Sagem flash on the Nokia 3310 DO NO TRY TO POWER ON THE PHONE, IT WON’T POWER ON!!!

5. Read the flash with Dejan or any other equipment that can read all 3310 Nokia flash.

6. You will have a bin file that you will save on your HDD.

7. Unsolder the Sagem flash from Nokia phone and put it back to Sagem phone. THE PHONE MUST WORK AGAIN!!!

8. Open the bin file with any bin editor (I used Winhex) and read field 0, 22 and the… that you will need for calculate the unlock code with any sagem calculator.

The code you get it is the unlock code.
work 100% ;)

[amine gsm maroc]

This operation it is not for beginners ;) , juniors or rookies!!!!

I will explain step by step. Works 100%

1. You must heat the flash IC of Sagem MyV 55, from 150 to 400 degree for about 10 minutes, but you must rise temperature progressive until you can pull it out from the black resin, or if you a solution which dissolve resin you can use it. At this point be very careful how you can get it out the flash with out destroy it.

2. You must heat and unsolder the flash from a Nokia 3310.

3. In place of Nokia 3310 flash put the Sagem flash that you unsoldered in the first place

4. After you soldered the Sagem flash on the Nokia 3310 DO NO TRY TO POWER ON THE PHONE, IT WON’T POWER ON!!!

5. Read the flash with Dejan or any other equipment that can read all 3310 Nokia flash.

6. You will have a bin file that you will save on your HDD.

7. Unsolder the Sagem flash from Nokia phone and put it back to Sagem phone. THE PHONE MUST WORK AGAIN!!!

8. Open the bin file with any bin editor (I used Winhex) and read field 0, 22 and the… that you will need for calculate the unlock code with any sagem calculator.

The code you get it is the unlock code.
its work 100% :)

[latigido]

@amine gsm maroc
Don`t spam forum !
Do you know what flash chips inside V55 and Nokia 3310? ;)
Do you know field format in new Sagems? :D
To be convincing, post here field 0; 251 or 252 and ID from one V55 unlocked with your famous solution!

;)

[GSM Coolhawk]

hehe

This he have taken from another post on the board ! Was posted several days ago, Just do a seach on V55 and you'll see. Solution not even his own. Solution does exist in theory, but I have not seen anybody actually confirm this, but if the solution really exist, then a very few select people know which addresses in full flash to get the Fields from ! And I aint one of them for info, so no "send me too"

Regards

[jusluke]

This operation it is not for beginners ;) , juniors or rookies!!!!

I will explain step by step. Works 100%

1. You must heat the flash IC of Sagem MyV 55, from 150 to 400 degree for about 10 minutes, but you must rise temperature progressive until you can pull it out from the black resin, or if you a solution which dissolve resin you can use it. At this point be very careful how you can get it out the flash with out destroy it.

2. You must heat and unsolder the flash from a Nokia 3310.

3. In place of Nokia 3310 flash put the Sagem flash that you unsoldered in the first place

4. After you soldered the Sagem flash on the Nokia 3310 DO NO TRY TO POWER ON THE PHONE, IT WON’T POWER ON!!!

5. Read the flash with Dejan or any other equipment that can read all 3310 Nokia flash.

6. You will have a bin file that you will save on your HDD.

7. Unsolder the Sagem flash from Nokia phone and put it back to Sagem phone. THE PHONE MUST WORK AGAIN!!!

8. Open the bin file with any bin editor (I used Winhex) and read field 0, 22 and the… that you will need for calculate the unlock code with any sagem calculator.

The code you get it is the unlock code.
its work 100% :)

yeah not really a good solution if you'd ask me even for the "not beginners" who wants to play with flash ic's this solution is too risky and not to mention its not "your" solution

[waleedkhalid]

we need safe solution for unlock my v55 any body help

[GSM SHADOW]

i'm sure soon there will be safe solution

[ramos]

ha ha ha :D
solution for expert from a beginner...let me laugh :D
why don't use JTAG interface if it's so easy to read flash components and fields?