Samsung Z107 UNLOCK SOLLUTION FREE

[forhike]

If you are locking for samung z107 unlock sollution, why don't you just try with same program that you have when unlocking a z105?

simple use. com connector and short tx and rx pin 2-3 on the (com)
use samsung original usb cable PCB157ULE

1. plug in phone install usb drivers
2. open QIWS_V1.16(Service)_041011.exe
3. plug in com adapter (tx and rx shorted)
4. check if program finds samung modem. (if not found, go back to 1)
5. press ok
6. press unlock, (if you get usb error try to go to 4 and change the usb comport manualy to something else)
7. if phone unlocked insert a gsm card (if you have problem with network just change it manualy to gsm instead of automatic)

links for program and cable information can be found here...
http://forum.gsmhosting.com/vbb/showthread.php?t=173873

i have nothin more to say...

exept.... why but agere attack when they probably use same sollution themself for z105 and z107

[SJS]

Yes. Working perfect. Thank you!

[Vervolf]

good news... regards

[gsm_koksi]

i have here a problem

i try it with a z100 datacable
connected pin 2-3 in female DB9 and to the green cable in the samung usb cable with a switch

samsung modem is in port 14

Serial com...Good
WAIT! Detect USB Port
Sucess: direct USB Port...
Searching Samsung Modem...
Usb Port Open Sucess
Lock Read Fail

any ideas where the failure can be?
thx

[SJS]

Also: You don,t need modify original samsung z107 cable. And change modem port to 4 or 5. Under 10. that works!

[gsm_koksi]

yes, this was the tiny failure

change port and work

thx stefan

[theXtreme]

working perfect
thanx mate ....

[drdjolens]

Nice work.

Thx. :)

[GSM MIND]

me try to make this cable and hope it will work for me


REGARDS

GSM MIND
STAND ALONE

[tele-teknik]

Nice work.

Thanks.............:)

[iserlohn]

No need to make the cable. Just use the original USB cale, and then make an adapter that short out pins 2 and 3 on your COM1. (You can just use a piece of wire to do this)

The software only checks the carrier on the COM port, and then it uses the USB serial port to do the unlock.

[Own]

@forhike
all work .....i tried with green wire more but not and i tried your solution ALL WORK and resolve phone freeze
BR
Own :D :D :D
but winimei z105 work with Z110?

[Nemooo]

WORKS!! great! Thanks forhike :)

[forhike]

Nice work.

Thanks.............:)


hehe perhaps it was bad move to write the sollution here =p
where are you from ?

[forhike]

@forhike
all work .....i tried with green wire more but not and i tried your solution ALL WORK and resolve phone freeze
BR
Own :D :D :D
but winimei z105 work with Z110?

i don't have any z110 for testing =/
does it exist in europe? or is it asia modell ?

[amitks_in]

hi plz help me in unlocking Z105 samsung

[forhike]

hi plz help me in unlocking Z105 samsung

what's your problem ?

[BadBoy1404]

Hi

Sorry but I can´t unlock my z107 with that programm!
i need a shematic for the cable!
please help me with that problem!

MFG BadBoy1404

[almedin]

hi @ all !

í've got troubles to understand your instruction, because im not as good as i thought in english , however ....

i didn't understand what to do with the cable , ( - saw a pic...) and what is that wit the pin "2-3" .... ???

it would be nice if somebody could give me en exact instruction or a link where i can get it in german , ....

and where i can get the software from ,

Thanks .... ;)

[forhike]

hi @ all !

í've got troubles to understand your instruction, because im not as good as i thought in english , however ....

i didn't understand what to do with the cable , ( - saw a pic...) and what is that wit the pin "2-3" .... ???

it would be nice if somebody could give me en exact instruction or a link where i can get it in german , ....

and where i can get the software from ,

Thanks .... ;)

http://webuser0.s23.deinprovider.de/Software/z105.rar

i can post a pic on the com pin 2-3 ("dongle") later when i get back home

[adel11]

you can read code NCK and enter manually

it is better than unlock directly

and for Nemooo dont forget yourself and write in english.verstanden ???

[gsmlab4u]

very good keep it up.

gsmlab4u

[amitks_in]

Thank U I will try and let u know,

[gsmlab4u]

hi members if anyone having Z105 unlocking soluation pls send message imm-dtly.

gsmlab4u

[kega234]

thanks rfor that goood job

[forhike]

hi members if anyone having Z105 unlocking soluation pls send message imm-dtly.

gsmlab4u


hello!

this works on z105 and z107
use same instructions =)

[Nemooo]

and for Nemooo dont forget yourself and write in english.verstanden ???Gone crazy? :mad:

I just translated the procedure posted by forhike for alamedin b/c he asked for a link of a german translation. :eek:

[TRIBULUSS]

[QUOTE=forhike]If you are locking for samung z107 unlock sollution, why don't you just try with same program that you have when unlocking a z105?

simple use. com connector and short tx and rx pin 2-3 on the (com)
use samsung original usb cable PCB157ULE

I HAVE SAM Z107 AND INSTAL SOVTVER AND DRAIVER IS OK.AI HAVE ORIGINAL CABLE FOR SAM 107.IF I VANT UNLOC PROGRAM WRITE...START UNLOCK,CHECK SERIAL COMUNIKACION WITH THE FONE,SERIAL COM - NG

THIS IS ALL
WHAT MUST AM DO IT::?????

WHAT IS IT Short tx and rx pin 2-3 o ---_?????? :mad: :mad: :mad: :mad: :mad: :mad: :mad:

[ReviveR]

Non-English posts are not allowed in any form here, sorry.









BR

[forhike]

[QUOTE=forhike]If you are locking for samung z107 unlock sollution, why don't you just try with same program that you have when unlocking a z105?

simple use. com connector and short tx and rx pin 2-3 on the (com)
use samsung original usb cable PCB157ULE

I HAVE SAM Z107 AND INSTAL SOVTVER AND DRAIVER IS OK.AI HAVE ORIGINAL CABLE FOR SAM 107.IF I VANT UNLOC PROGRAM WRITE...START UNLOCK,CHECK SERIAL COMUNIKACION WITH THE FONE,SERIAL COM - NG

THIS IS ALL
WHAT MUST AM DO IT::?????

WHAT IS IT Short tx and rx pin 2-3 o ---_?????? :mad: :mad: :mad: :mad: :mad: :mad: :mad:


you have to use a com connector and short (connect pin 2-3) tx and rx)
that will make it all happend =)

you can for example take the connector from a old com mouse or anything like that.

[Nemooo]

Non-English posts are not allowed in any form here, sorry.
ok, then go **** yourself.

[forhike]

ok, then go **** yourself.

hello!

it was werry kind of you to translate the posts, but pls for everyone to feel happy on this forum, watch the language

[gsmlab4u]

thnaks broth, i tried to unlock z105. i made cable and tel which sw shall i use?

gsmlab4u

[forhike]

thnaks broth, i tried to unlock z105. i made cable and tel which sw shall i use?

gsmlab4u

http://webuser0.s23.deinprovider.de/Software/z105.rar

[gsmlab4u]

if u dont mind pls send me z105 unlocking sw.

gsmlab4u

[forhike]

if u dont mind pls send me z105 unlocking sw.

gsmlab4u

hello! wats wrong with the link above ? =)

just press the link

[iserlohn]

You don't need to special cable, just put a wire to short out pin 2 and 3 on your serial port. Then use your USB cable to flash.

[joe2517]

i have a p107 & x426 samsung cell locked can some help me please

[Myco1GSM]

Hi all

ALL UNDERSTOOD WELL & clear :)

USB Cable made :D
Fone found ;)
Modem on COM 5 :cool:
but i dont have serial port :confused:

program looks for COM than stops with error

P.S. when modem on COM-5 & run the program i get "cant open COM-1" error.

Any Ideas, please

Thanks 1000 X in advance

[joe2517]

can u unlock a sgh-p107 or sgh-x426 samsung network locked

[pyroz]

I need modem driver for Z107v
Z105 drivers dont work :(

br,
pyroz

[CPUKILLER]

[QUOTE=forhike]If you are locking for samung z107 unlock sollution, why don't you just try with same program that you have when unlocking a z105?

simple use. com connector and short tx and rx pin 2-3 on the (com)
use samsung original usb cable PCB157ULE

I HAVE SAM Z107 AND INSTAL SOVTVER AND DRAIVER IS OK.AI HAVE ORIGINAL CABLE FOR SAM 107.IF I VANT UNLOC PROGRAM WRITE...START UNLOCK,CHECK SERIAL COMUNIKACION WITH THE FONE,SERIAL COM - NG

THIS IS ALL
WHAT MUST AM DO IT::?????

WHAT IS IT Short tx and rx pin 2-3 o ---_?????? :mad: :mad: :mad: :mad: :mad: :mad: :mad: USE WIN 98 AND DB9 CONNECTOR 2AND 3 PINS SHORTED

[CPUKILLER]

i don't have any z110 for testing =/
does it exist in europe? or is it asia modell ?
THANKS ALOT ITS A GREAT SOLUTION ATLEAST FOR ME IN MY COUNTRY ILOVE THIS FORUM

[byteforce]

I have a Z107 from Orange. And I am right now making the cables, but I don't see anywhere on WINIMEI program the option for Orange operator. What I must select?
thanks in advance

[byteforce]

I already made correctly the Z107 cable following the pinout, but Windows is not detecting at all the the phone. Should Windows do it if I have made the cable correctly?
thanks in advance

[byteforce]

Referring to the z105cable.rar there is this pinout:
USB Connector S100 Connector

1 GND(black)----------------- 5
2 D1 (green)---------------- 18
3 D0 (white)---------------- 16
4 +5V (red)----------------- 19

I have connected correctly according to this pinout, but I have no luck.
While on another tutorial that I found on the web named: "z105 detailed phone freeze remove tutorial" there is told that you must use the s100 connector, and we all know that S100 has a completely different pinout from that above mentioned by me.
Any advice would be appreciated.

[byteforce]

So nobody has an idea? To help me?

[forhike]

use s100 connector and soldier it acording to the z105 pinout and it will work

[tanh]

1. Download correct Driver Modem http://org.downloadcenter.samsung.com/downloadfile/ContentsFile.aspx?CDSite=HQ&CttFileID=194044&CDCttType=SW&ModelType=N&ModelName=SGH-Z107&VPath=SW/200410/20041025141606890_Easy_Studio_for_Z10x.exe
2. Referring to the z105cable.rar there is this pinout:
USB Connector S100 Connector
1 GND(black)--5. 2 D1 (green)--18. 3 D0 (white)--16
4 +5V (red)--19
3. Built Dongle com port with short pin 2&3
4. Phone ON--select Unlock -- Pass
Working with QIWS_V1.16(Service)_041011.exe

[ARDIC]

super ;) z107 unlocke

[mourad_t]

Hi! (Urgent)

I want to know how to lock this Z107v to its original operator?
I tried lock function, but doesn't help?
'cause I unlocked this Z107v, and I want to relock it!!!

[mourad_t]

Hi! (Urgent)

I want to know how to lock this Z107v to its original operator?
I tried lock function, but doesn't help?
'cause I unlocked this Z107v, and I want to relock it!!!

Problem solved :)
Relocked-back :D

Thanks, bye

[orao]

All works fine,if somebody need help,contakt me

[ARDIC]

If you are locking for samung z107 unlock sollution, why don't you just try with same program that you have when unlocking a z105?

simple use. com connector and short tx and rx pin 2-3 on the (com)
use samsung original usb cable PCB157ULE

1. plug in phone install usb drivers
2. open QIWS_V1.16(Service)_041011.exe
3. plug in com adapter (tx and rx shorted)
4. check if program finds samung modem. (if not found, go back to 1)
5. press ok
6. press unlock, (if you get usb error try to go to 4 and change the usb comport manualy to something else)
7. if phone unlocked insert a gsm card (if you have problem with network just change it manualy to gsm instead of automatic)

links for program and cable information can be found here...
http://forum.gsmhosting.com/vbb/showthread.php?t=173873

i have nothin more to say...

exept.... why but agere attack when they probably use same sollution themself for z105 and z107

[senkron24]

usb port fail pls help me this sulution :(