View Full Version : Sagem MY-V55 dead after direct unlock with sws-sag 1.5
Hi to all!
Pleaze help me...
I have My-v55 with start up failure (when i pres power ON the phone il dont power ON ,only blinking display) and that is all.
Program readed code ..., i remuved batery and puth in back and powered phone on ...program sai unlocked phone ok. After this i asembled phone and when i phut a sim card inside phone don't start only dysplay blincking.
Thank you!
Best Regards,
Jean
strangerboy
03-23-2005, 20:58
have you checked battery?????? lloooll
Yes of corse man ...Batery its full 4 V... loool
Really strange one here, but anyway check screen connection point. You may need to clean both connecting ends slightly, then connect the screen.
Really strange one here, but anyway check screen connection point. You may need to clean both connecting ends slightly, then connect the screen.
I clean every conector and charging conector but phone dont power ON withut screen conected.(only with batery and when i pres pwer buton nothing hapened)
When i atach scren on phone and i pres power ON the phone only strange dysplay blinking....
Any one have an idea....?????
mustapha.2
03-23-2005, 23:44
scrd II is the best :D sws is :(
scrd II is the best :D sws is :(
try to help this is stupid response
Hi to all!
Pleaze help me...
I have My-v55 with start up failure (when i pres power ON the phone il dont power ON ,only blinking display) and that is all.
Program readed code ..., i remuved batery and puth in back and powered phone on ...program sai unlocked phone ok. After this i asembled phone and when i phut a sim card inside phone don't start only dysplay blincking.
Thank you!
Best Regards,
Jean
try to change diode near conector and teste conector if is good !
good chance :)
moonfighter
03-24-2005, 01:24
try to pwr on with charger or try to reunlock
scdrII is good?there isa an opption to backup flash in fones??,try to unlock again dont do tuch anything in fone parts just unlock again....
try 2 service d phone, by urself relax couple it back, if no progress i have flash files 4 it , pm me ,save
GSM MIND
03-24-2005, 13:38
Hi to all!
Pleaze help me...
I have My-v55 with start up failure (when i pres power ON the phone il dont power ON ,only blinking display) and that is all.
Program readed code ..., i remuved batery and puth in back and powered phone on ...program sai unlocked phone ok. After this i asembled phone and when i phut a sim card inside phone don't start only dysplay blincking.
Thank you!
Best Regards,
Jean
MATE ONCE ME ALSO GOT THIS PROBLEM ITS NOT SOFTWARE FAULT AS I THINK U NEED TO CHECK ITS BATTARY CONECTOR AND PHONE CONECTOR TOO IT SHOULD BE THE PROBLEM OF UR PHONE CONECTOR HOPE IT WILL SOLVE UR PROBLEM
REGARDS
GSM MIND
STAND ALONE
Hi to all and thank you for your help .
I try all yours sugestions but phone its dead (same problem).
:(
I bougt one new phone for cusstomer and nou i try again to fix my problem.
Thank you again.
Best Regards,
Jean
What version of my soft have you use ?
can you read data of your phone by cable and send it here , say me Hash table of your phone ,
try to direct unlock again
BR
mr_x4you
03-25-2005, 23:25
Hi to all and thank you for your help .
I try all yours sugestions but phone its dead (same problem).
:(
I bougt one new phone for cusstomer and nou i try again to fix my problem.
Thank you again.
Best Regards,
Jean
Next time try not to use direct unlock function, read code and type it by keyboard ! And don't post same problem on all forums you are registered, here is enough
hitibiti
03-26-2005, 00:06
never do direct unlock that's kill the phone jut read cod and type it is so easy
;)
@julvir
Hi !
I use version 1.5 of sws-sag and direct unlock function.
Phone not conect again with software . I think il is H22 table .
Thank You!
Next time try not to use direct unlock function, read code and type it by keyboard ! And don't post same problem on all forums you are registered, here is enough
Hi mr_x4you
1.I ned real help to solve mi problem not features sugestions....(of topic things)
2.I not posted my problem on "all forums " where i am loged on.......(I posted only in a Romainian forum , and how you know romainian unlockers hawe good experiences and good peoples)
Best Regards,
Jean
mr_x4you
03-26-2005, 01:50
I understand that, but you think Julvir reads romanian forums ? This is the place you might get some help
@jean' and other
direct unlock will never kill your phone.. soft just write same filed..if data is not correct in this specified filed all that you can get is phone locked without card inside or something like that but killed never.
Your problem is hardware .. replace battery connectore all times make this problem ..test your phone with charger and without battery .. replace LCD or just remove it and try power on your phone ..see phone connectore if same pin are short-cuted..
i hope that help you to resolve your problem
Regards,
@moderator
This is the only place or the best place?hehe,i don't think so!
Problema e inca nerezolvata,se pare...unde ti-e patriotismul???
Sorry guys for non english.
Regards,
XCHRIS
I understand that, but you think Julvir reads romanian forums ? This is the place you might get some help
Da , ce faci ? :)
bine ,
@jean , as you see , your phone have problem , but is not because of direct unlock , direct unlock write code in phone like if you tape by hand ,
surly hardware
BR
:D :) so ,Julvir read romanian forum!
Good news...;)
Regards,
XCHRIS
I understand that, but you think Julvir reads romanian forums ? This is the place you might get some help
Hi!
Mi topic from romainian forum its not for julvir (but lyke you read in up topic Julvir read rumainian forum :D ) its for Romainian unlockers and for hiers experiences... (this topic its for julvir)....
Best Regards,
Jean
@jean' and other
direct unlock will never kill your phone.. soft just write same filed..if data is not correct in this specified filed all that you can get is phone locked without card inside or something like that but killed never.
Your problem is hardware .. replace battery connectore all times make this problem ..test your phone with charger and without battery .. replace LCD or just remove it and try power on your phone ..see phone connectore if same pin are short-cuted..
i hope that help you to resolve your problem
Regards,
I am on same part with you (i tested all this posibilitis but phone stil dead)
Mi question is why phone worked first time , and after unlock only dysplay blynking with display (no keypad leds on) , and withut dysplay phone dont power on ??? (I unlocked (direct unlock) more than 80 pcs of new sagem with this soft withut any problems .........and now........... :mad: )
Best Regards,
Jean
AntiXrysT
03-27-2005, 13:55
so where do u get this kool soft 4 myv55?i aint paying 4 it if its gonna break my fone.
Da , ce faci ? :)
bine ,
@jean , as you see , your phone have problem , but is not because of direct unlock , direct unlock write code in phone like if you tape by hand ,
surly hardware
BR
Hehehe, Julvir welcome in www.gsmforum.ro :-)
Best regards,
Irinel
:)
Finaly problem solved with scrd 2 flasher.
Phone its again alive and fully working.
with scdrII i don't have any problem with all new sagem it is the best bway to unlock ur phone sws-sagem is a ****!!!
i have the test them both!!
Hi to all!
Pleaze help me...
I have My-v55 with start up failure (when i pres power ON the phone il dont power ON ,only blinking display) and that is all.
Program readed code ..., i remuved batery and puth in back and powered phone on ...program sai unlocked phone ok. After this i asembled phone and when i phut a sim card inside phone don't start only dysplay blincking.
Thank you!
Best Regards,
Jean
hi
If you have problem with software with this phone
TRY WRITE FLASH FILE VIA SCDR2
100 % PHONE UP
- open corect flash in buffor
- conect TP Adapter
- conect special data cable from SCDR 2 set
- start write flash
after write flash file phone up 100%
( dont forget about power , battery full or external read conector to "+" from batery conector on phone )
b r :)
GSMinfo
-
japunlock
04-30-2005, 00:10
Da , ce faci ? :)
bine ,
@jean , as you see , your phone have problem , but is not because of direct unlock , direct unlock write code in phone like if you tape by hand ,
surly hardware
BR
if this is true then why phone ends permanently locked after direct unlock???
giorgi2002
04-30-2005, 00:56
scdr2 flasher repair this phone 1000%
tj27.com
05-01-2005, 11:06
haet d phone & flash it with scdr 2 it most power up
tj27.com
05-01-2005, 11:08
haet d phone & flash it with scdr2 it most power up
i have the same problem with sagem x2, after unlock it dead
can help me, thancks
try sagmaster product
write flash to phone
after this phone up 100%
all software problem solve
b r
I've same problem with MYX5 dead with direct unlock, anyone can help please...
V.B.R
latigido
06-18-2005, 11:49
Direct unlock with wrong code has as result permanently locked phone!
Realy good box ;) will repair phone after repetition of the unlock procedure.
For resolving this problem SagemJTAGunlocker gives additional way - "Restore default lock" procedure.
I not recommend phone flashing for resolving such simple problem! :)
BR!
Thanks for your speed latigido I will test it...
B.R
tomaszwl
07-02-2005, 11:53
Hi,
I have few problems, some off topic, but I have no other way to make it.
First:
how can I reactivate the support for SWS-SAG box? I was a registered user, but I cannot login using my login and password - mister Julvir doesn't answer my e-mails (that's not nice).
Second:
does the sws-sag box have possibility to unlock sagem myx1 twin?
Regards,
Tomasz WL
hi
can sws-sag flash sagem phone
The_Gorr
08-18-2005, 15:02
not for now
maybe soon my freind :D :D :D
hi
can sws-sag flash sagem phone