My T10 00W25 say: ERROR03

[neprom]

Hi all ! My t10 if flashing with ATR5.3 say this (progress indicator stop in 99%) :( how ? please help me ! thnx

[GsmSolution]

That 99% stop because is your cable problem.
100% cable problem.Check it.

[BillyJoe]

Maybe it isn't a cable error, sometimes, with f***** phones I saw that error (with a cable working 100%), You have to try one, two,..., or a combination of this: (test)

-flash, and before get 99% disconect phone, you will see if the same error happends. To know if it is a cable prob.

-Flash, and when finished erasing, disconect and flash with NE-Tool121.

-rewrite another working eeprom to your phone.

BR
BillyJoe

[Unlocker AL]

Yes, I also have a T10 that stops 99% in eeprom read. And my cable is working 100%. I think is the problem of bad eeprom... :mad:

regards,

[GsmSolution]

Hi all
I say is cable problem because i have many type of cable and i have test.I made myself working100%[misiek schematic].I have 5 type factory made cable.3 type can use in flashing and unlocking.And 2 type only can use in unlocking.
Flashing also can but in old model like 6xx,7xx.if you are not using misiek schematic.And use another schematic try to use external 5v.
:D :eek: ;) :cool: :o

[GsmSolution]

The 2 type can't use in atr 99% stop.I have test in ne-tool sometime error.Use in saras workshop not working. :mad:

[neprom]

Hi all ! I'm uploaded a new working eeprom, but phone is already STOP in flashing. (ERROR03, 99%) Cable is working my A1018. (maybe a Flash IC error ?) Thnx all

[Vlado Kusnirak]

Try to use ATR 5.3
1. Repair phone with original IMEI
2. Flash it with T18r5aeu (on Zulea's page)
3. Use NEtool 1.21 with flash in000114.r4a

Vlado

[GsmSolution]

Originally posted by neprom:
<STRONG>Hi all ! I'm uploaded a new working eeprom, but phone is already STOP in flashing. (ERROR03, 99%) Cable is working my A1018. (maybe a Flash IC error ?) Thnx all</STRONG>

yes U right also can be like that.Try to solder to touch up the flash ic.Better use hot air to flow the flash ic.maybe ok.Try it. :D

[Olexa]

And not use ATR 5.x for flashing phone..Only for unlocking..

For flashing use Ericsson Workshop or ne-tool (sometine not worked correctly too)..

[gurmk]

Could anybody give me the homepage address of Zulea, I have ATR 4.2 but need a later version

[vala]

www.zulea.com (http://www.zulea.com)

[Stryker]

hi to all!

one thing ive known about stopping at 99% error03 is that it depends on the computer. why? because ive used ATR 5x on my laptop, then its error. On my desktop, flash/unlock succesfully! My cable is 100% working on all ericsson softwares...

regards ;)

[HFP]

Hi! Try ER2000 @ TxxWEST ! Work 1000% with all T10.
Regards.
HFP

[Syko]

Hi all,
read old post http://gsm.thoic.net/cgi-bin/ultimatebb.cgi?ubb=get_topic&f=26&t=000470

and you may see that E3 eprom erase problem, was mainlt attributed to battery.
we found that if battery is 1/2 to 3/4 full then this does not happen so much.
Also , often after getting this problem you get dead phone (will not switch on).

If you have this then you can try dark Lemmings revive solution, or remove eeprom and reprogram with pony prog (this is what I had to do)

[farry]

hi nepram

i was getting the same message (03), heres how i solved my problem.as syko said try different state of the charge of the batterie from 3 minutes charge!! to half and then3/4 full believe me it worked after the 6th time!!! 1000%( better still use 4 different state of the charge) beleive me it works, good luck! theres nothing else wrong any where else.

farry

[F]

I've had the same problem too, the battery was too charged. It always works for me when the phone is half-charged.

[Altern8]

Yes i had this problem too. For the best work your batery must voltage between +5.0 & +5.08 v . Than work 100% and ofcourse you must have clean connector on your phone.

[neprom]

Hi all ! Thnx for all solution. MY PHONE IS LIVE !!!! Very, very thnx.

Regards NePrOm :)

[sokrateng]

Hi my Er2000 and Er2001 doesnt run. it is no flashing to phone. ı wait very much minutes but doesnt run...why....Er2000 and 2001 why doesnt run?????