View Full Version : Problems with 6680
Murat Bekar
10-29-2005, 19:32
Processing File: RM36_4.050407_B5.C0R
Boot...
rap3gv2_2nd.fg
RAP3Gv2_algo.fg
helen3_2nd.fg
h3_sam_nand_gbbm.fg
Erase[37.21 MB]...Waiting response for 90 Sec...
%%%%%%%% ERROR ERASING:
Failed at address 00000000
5pin cable not working. I am using 10 to 8 adaptor :(
Murat Bekar
10-29-2005, 19:54
only ppm flashing works. but I can not erase/flash mcu
Murat Bekar
10-30-2005, 11:29
any idea about this problem ?? I am a bit dissatisfied until yesterday.
5 pin 6680 cable comes with mtbox -> not working, even not showing which loaders are being sent to phone
with another cable I got this error 5 pin cable .
Processing File: RM36_4.050407_B5.C0R
Boot...
rap3gv2_2nd.fg
RAP3Gv2_algo.fg
helen3_2nd.fg
h3_sam_nand_gbbm.fg
Erase[37.21 MB]...Waiting response for 90 Sec...
%%%%%%%% ERROR ERASING:
Failed at address 00000000
???
any solution
Regards
isaackenny
10-30-2005, 12:34
have u try untick disable VPP flashing
Murat Bekar
10-30-2005, 12:48
yes tried all combinations.
repaired phone with HWK :(. I think GT must work hard for their new product.
Regards
bestncheap
10-30-2005, 15:36
i have same problem with u.. can not flash with mt box....
poor box.. :(
but with jaf can revive the phone..
Pleaseee updatee...
BR
BNC
i have same problem with u.. can not flash with mt box....
poor box.. :(
but with jaf can revive the phone..
Pleaseee updatee...
BR
BNC
HI
Dear frend this is 100% cable problem (your vpp pin is not on corect place )
we alredy fix version for BB5 phones disable vpp work now on bb5 also
BR GT
bestncheap
10-31-2005, 05:15
cable 5pin or 7pin?
BR
BnC
MicrostarGSM®
10-31-2005, 06:55
cable 5pin or 7pin?
BR
BnC
tested perfect for 6680 with normal cable 5pin with adaptor connected here is the result below
both of your problem probaly is cable check your cable conenction
Phone is in: Unknown mode
Product Profile file is: RM36_4.050407_als_GsmOnly.pp
Model: RM-36 ( RM-36)
V 04wk47v43.1/26-05-05/RM-36 (c) Nokia.
Production serial number SBF424116
Product code 0524033
Module code
Basic production code 0516030
Flash code
Order number
Product specific data
Long production SN
MCU SW version V 04wk47v43.1/26-05-05/RM-36/(c) Nokia.
HW version 6010
PCI version
RFIC version 150a160e
DSP version 04w47v22
LCD version 2721308
APE SW Core version V 3.04.37/01-06-05/RM-36/(c) NOKIA.
APE Variant version V 3.04.37-Euro1/01-06-05/RM-36/(c) NOKIA.
Retu version 32
Tahvo version 41
APE HW version 256
APE ADSP SW version 52041
Camera version 3
IMEI: 35706xxxxxxxxxx
Processing File: RM36_4.050407_B5.C0R
Boot...Erase[37.21 MB]...in 45.86s, Flash[20.23 MB]...in 68.18s
* * Processed file in 123.00 seconds
Processing File: RM36_4.050407_B5.v35
Boot...Erase[0.00 MB]...in 0.00s, Flash[4.51 MB]...in 24.67s
* * Processed file in 33.53 seconds
* * * Phone flashing done in 2:36 minutes
Pooling mode for full factory set...
Factory Default Settings...OK
Pooling mode for profile update...
Sending Profile to Phone...OK
hi ,,
problem is cable i get this error with jaf cable modified ,,,but i got new cable and here are results
Processing File: RM1_4.050340_B4.C0R
Boot...
rap3gv2_2nd.fg
RAP3Gv3_algo.fg
helen3_2nd.fg
h3_sam_nand_gbbm.fg
Erase[37.21 MB]...Waiting response for 90 Sec...in 39.45s
Flash[20.25 MB]...in 70.88s
* * Processed file in 119.47 seconds
Processing File: RM1_4.050340.v62
Boot...
rap3gv2_2nd.fg
RAP3Gv3_algo.fg
helen3_2nd.fg
h3_sam_nand_gbbm.fg
Erase[0.00 MB]...in 0.00s
Flash[5.16 MB]...in 30.78s
* * Processed file in 39.83 seconds
* * * Phone flashing done in 2:39 minutes
Pooling mode for profile update...
Sending Profile to Phone...ok
reg
nik
I also have this problem with my MT-Box when Flashing my 6680 phone????
I use both 5 and 7 pins cable but still error booting.....
can anyone tell what actually happen here and got any solution for this?
MicrostarGSM®
11-02-2005, 15:30
I also have this problem with my MT-Box when Flashing my 6680 phone????
I use both 5 and 7 pins cable but still error booting.....
can anyone tell what actually happen here and got any solution for this?
lol have u use the adaptor for MT-Box
if you are using cables for (Griffin,JAF,UFS) it will not works wihtout the adaptor, make sure that you attach the adaptor .
Murat Bekar
11-02-2005, 18:36
I ve the same problem with 6680 and I use mtbox cable adaptor.. but still the same problem..
MicrostarGSM®
11-02-2005, 18:56
I ve the same problem with 6680 and I use mtbox cable adaptor.. but still the same problem..
check your cable or connection
100% connection problem
Murat Bekar
11-02-2005, 20:40
mate. I ve tried with 3 different cable. 2 of them 5 pins 1 is 7 pins
tried with disabling vpp..
funny thing is cables are working with griffin 2.0895. I flashed the phone with griffin 2.0895 but with mtbox it gives erase error after timeout...
no problem with other phones. I use cable adaptor...
is there a cable schema for 6680 to use with mtbox ??
and cable for mtbox is different from other cables ( griffin, hwk )
Regards
MicrostarGSM®
11-02-2005, 20:57
mate. I ve tried with 3 different cable. 2 of them 5 pins 1 is 7 pins
tried with disabling vpp..
funny thing is cables are working with griffin 2.0895. I flashed the phone with griffin 2.0895 but with mtbox it gives erase error after timeout...
no problem with other phones. I use cable adaptor...
is there a cable schema for 6680 to use with mtbox ??
and cable for mtbox is different from other cables ( griffin, hwk )
Regards
lol..
u still not understand
u need to attach this adaptor to the box then only the cable attach to this adaptor
http://www.mt-box.org/image/accessories/large/mtbox_adaper.jpg
coz your grifficable is 8 pin RJ45 and MT-Box is 10pin RJ48
MicrostarGSM®
11-02-2005, 21:35
there is new version release
whit this new version for flashing 6680 please chek disable VPP
Murat Bekar
11-03-2005, 10:04
@microstargsm
I am not a newbie friend, I can understand things and of course I am using mtbox cable adaptor for 8 pin cables. but I still have the same problem. I dont have flashing problem with 6630 6600 6260 etc but for 6680 I ve serious problems. I am trying several different cables but they give totally same error. ( for 6680 and 6681 only )
Murat Bekar
11-03-2005, 10:06
and I can read phone info with the cable. ( so this means I am using CABLE ADAPTOR )
MicrostarGSM®
11-04-2005, 12:53
new version release today check here
http://forum.gsmhosting.com/vbb/showthread.php?t=243024
bugs fixed for BB5
MTB_NK_1.081
Murat Bekar
11-05-2005, 16:59
now works ok .. I successfully flashed a 6680 with the same cable and same adaptor.
Regards
now works ok .. I successfully flashed a 6680 with the same cable and same adaptor.
Regards
HI
I am really happy you solve problem.(cable)
Just for info 1.081 bug fix have nothing connected whit your problem.
now connect phone and run old version you weel see is work.
BR GT
Murat Bekar
11-05-2005, 17:32
@andro
that is really funny. I just flashed with 1.081 first time, I will test older version when I receive one more bb5
Regards and thanks for your interest to my problem.