Unlock CF75

[The Beast]

Hi,
I tried to unlock a CF 75 today using the testpoint instruction on support(black needle), but was not able to unlock the phone, the phone goes into service mode and then this apears: Failed to read info version might be >37.

I tried alot of times, but still no success, what am I doing wrong?

Please help SST-Team.

[tobi2]

your mark in soft test point or not
mark this and tray after that

[SST-GSM]

Hi,
I tried to unlock a CF 75 today using the testpoint instruction on support(black needle), but was not able to unlock the phone, the phone goes into service mode and then this apears: Failed to read info version might be >37.
I tried alot of times, but still no success, what am I doing wrong?
Please help SST-Team.
please try test-point mode.
CF75 is support only via TP mode.
Picture is i n the pdf manual in the support area

[The Beast]

SST-Team please help, I have followed the instructionof testpoint but, when I click unlock it tell me to connect needle to testpoint, and then it says remove testpoint, and then it keeps on retrying and the process starts again, I did not get further than that?

I'm using the testpoint mode and I'm using only the black needel, the power connector and the plug to the phone, the red needle I'm not using.

Can you please help me? What more can I try? I have 5 peice here that needs unlocking

Thanks

[SST-GSM]

SST-Team please help, I have followed the instructionof testpoint but, when I click unlock it tell me to connect needle to testpoint, and then it says remove testpoint, and then it keeps on retrying and the process starts again, I did not get further than that?
I'm using the testpoint mode and I'm using only the black needel, the power connector and the plug to the phone, the red needle I'm not using.
Can you please help me? What more can I try? I have 5 peice here that needs unlocking
Thanks
If SST gives always retrying on connection please restart SST and if it does not help unplug the dongle and plug it in again.
If it does not helps connect to support@sst-gsm.com
Please also tell us if it happens with this model only

[The Beast]

I tried it again, when the software tell me to connect the needle to testpoint, I do it, and then when the it tells me to remove I don't remove it, than it says reading data but stop till there, than nothing happens, if I follow the software to remove needle it will ask again to put needle.
The software says "starting unlocking procedure" and reading data on the bottom, and then nothing happens, it stops there.

I have succesfully unlocked a CF62

I appreciate the help.
Any more advice?
THanks

[delta master]

do you have infity-box mate cl75 can unlock by it using serial cable you dont need to use test-point.

[darie cruz]

I tried it again, when the software tell me to connect the needle to testpoint, I do it, and then when the it tells me to remove I don't remove it, than it says reading data but stop till there, than nothing happens, if I follow the software to remove needle it will ask again to put needle.
The software says "starting unlocking procedure" and reading data on the bottom, and then nothing happens, it stops


don't panic mate......did u see what the soft says : remove testpoint

just do it then wait for another instruction and you'll see the difference.....though a bit tricky

br

[huzsolt]

do you have infity-box mate cl75 can unlock by it using serial cable you dont need to use test-point.

he speaks abut CF75, not CL75, two different platforms

[Balkanjia]

WELL i do it by Unibox and when SST asc me to remove the testpoint I do it axactly than stops any TX or RX comunication the phone swiches off i think that the boot loader is bad or there are another flash chip that is not supported

[SST-GSM]

WELL i do it by Unibox and when SST asc me to remove the testpoint I do it axactly than stops any TX or RX comunication the phone swiches off i think that the boot loader is bad or there are another flash chip that is not supported
No the problem is not in the bootloader!
The problem is in the Rx input level that your unibox needs.
We have designed cables and devices that will work better with Benq -Siemens phones.Please make sure that the cables you use are aproved by SST-GSM.