View Full Version : Samsung D600 decharging battery
D600 full charged battery but it decharged after 2 or 3 hours, i have changed 3 battery and same probleme. any solution ?
smart phones
02-28-2006, 00:32
mate same problem somebody please help relly ******* me off i do the same thing used 4 batries
@Aymen G
try to check charging componement after drinking 10 or 20 biers and i'm sure you will find the solution:D
br
@infogsm
it's a unique solution :D
svukov21
02-28-2006, 14:45
My friend and I have new D600 phones and have same problem.If I charge my phone when it is powered up battery last for maybe 6-7 hours but if I charged it when it is powered OFF it last for 2-3 days.
So try to charge your phone when it is powered OFF.
WBR
the phone is always in my shop and I don't have a solution !!!!
The solution is simple :
Just Flash It With Latest Version .I many solved many case wht thi troubles
The best whisch
Amartt :D
The solution is simple :
Just Flash It With Latest Version .I many solved many case wht thi troubles
The best whisch
Amartt :D
same plob ::::::::::::::::::::
Ok
1 . Be sure that u use original"s batteries
http://www.cell-phones1.com/accessories/parts/samsung-d410-battery.jpg : No original :rolleyes:
No original 50 % cause severals fails ( Chargin , Troubles in Tx / Rx calls , Hot movil :D " whit sane actitud " :p , Etc
2 .Ok trouble Persist :
Check the conection plataform Pin by pin and try to resold very carefull whit
a little Flux and pen souder 16 W ( Only use 16 W fine point be carefull ):eek:
Resold the base in board conector"s batterie , use preferible souder 16 W ;)
3 . Check all the diodes whit continuity around on the Charge circuit this diodes dont have continuity (off ) Diode good http://forum.gsmhosting.com/ubb/icons/icon10.gif , continuity (on) Diode bad http://forum.gsmhosting.com/ubb/icons/icon9.gif.
Ok Check again all the diodes whit continuity whit respect to the earth , continuity (off ) diode bad , continuity (on ) diode good .
Make this test whit the board out . :p
4 - Check all the condesator ( capacitours )whit continuity
around on the Charge circuit ( continuity on ) = Bad ( continuity off ) = good
5 - In several models when the P"A is in short , him put like that wire , and consumed all the batteries http://forum.gsmhosting.com/ubb/icons/icon11.gif , But be sure that the phone make the Tx / Rx well If not the cause to the trouble can be in the P"A
U can post a Pic on the model , step by step can be explain better
Txs
Best R
Amartt [
Yesterday same problem with quick discharge, changed charging IC and same problem, changed lcd and now working fine!
try this code maybe help *#1234#
jasko2000
04-23-2006, 19:34
Temporary solution:
After charging battery remove battery and put it back.
Permanently solution:
Flash phone with last software
Which is latest software version for D600, in my phone I have D600XFEJ5.
Is there exist any newer version?
Thank you.
I think D600XEFC1(march 2006) is lastest version!?
Yesterday same problem with quick discharge, changed charging IC and same problem, changed lcd and now working fine!
most probably not lcd fault. But when opened and closed phone, connectors started making good contact.
GSM WIZARD
08-01-2006, 17:49
help me with d600 was not showing battery now off after trying to change power ic.now not powering.i tried to test the power ic on another phone,it works fine.what should i do?
FRIENDS, WHY SHOULD WE FORGET MOBILE IMPEDENCE ALL THE TIME?? WE HAVE 1st TO CHECK OHM BETWEEN BATTERY TIPS ON THE BOARD, IT SHOULD BE IN BETWEEN 300 OHM &7OO OHM -OTHER DIRECTION INFINITY- IF WE HAVE MEASURE LESS THAN 300 OHM ,THEN WE HAVE BATTERY LEAKAGE ACCORDING TO HOW MUCH LESS THAN 300 OHM (WE COULD HAVE THIS MEASURE ONLY 20 OHM AT MOBILE WHILE IT WORKS BUT OFF COURSE TOO MUCH LEAKAGE) IF WE HAVE EQUAL VALUES AT BOTH DIRECTIONS (50 OHM &5O OHM FOR EXAMP), WE GET ALSO THE SAME RESULT,
THEN SOLUTION IS TO DEAL WITH PARTS ON BATTERY LINE EITHER BY REHOT ,OR BY CHANGE AND CHECK EVERYTIME ,GOOD LUCK
AHMED TAHSEEN