PDA

View Full Version : Unlocking USB-Smart and UFS3/ Twister

Jankovic
03-07-2006, 19:19
Hello

Today I try Unlock X660 With SAM Tool 1.06 and Choose UFS .... Phone Powered ON And Start Unlock Process But get Error TIMEOUT etc etc..... Please Check this and give advice how to ..... Try to change Speed .... Cable Is OK later phone unlocked By UFS3 .......

Mario
Bernie
03-07-2006, 20:19
I have the same problem with one X640, did not work with usbsmart but with same cable unlock was fine with ufs-samtool


Br
Bernie
uffehbg
03-07-2006, 23:11
i have the same problem with a x460!
does samsung tool work?
Phantom
03-07-2006, 23:46
I have the same problem with one X640, did not work with usbsmart but with same cable unlock was fine with ufs-samtool


Br
Bernie

Same here. Does not work
Phantom
03-07-2006, 23:47
I have the same problem with one X640, did not work with usbsmart but with same cable unlock was fine with ufs-samtool


Br
Bernie

I get same result as Bernie.
easternlm
03-08-2006, 08:47
take out your bettery and try again.....without it
dani146
03-08-2006, 09:50
Hello

Today I try Unlock X660 With SAM Tool 1.06 and Choose UFS .... Phone Powered ON And Start Unlock Process But get Error TIMEOUT etc etc..... Please Check this and give advice how to ..... Try to change Speed .... Cable Is OK later phone unlocked By UFS3 .......

Mario

try this new release:
http://forum.gsmhosting.com/vbb/showthread.php?p=1626604#post1626604
Phantom
03-08-2006, 12:38
try this new release:
http://forum.gsmhosting.com/vbb/showthread.php?p=1626604#post1626604

Thanks Dani for the update.

I still have problems with E700.

As a suggestion, could you please add an *ini into the proggy where your default settings will be remembered? It can be quite tedious to reconfigure the comm settings everytime you want to use the sw.

Thanks.
uffehbg
03-08-2006, 13:22
still dont work with the x460 and x640!!!!!!!
i use 15in1 santel cables and it shold work shouldnt it?
have any one unlocked these modells?

uffe
dani146
03-08-2006, 14:34
Thanks Dani for the update.

I still have problems with E700.
As a suggestion, could you please add an *ini into the proggy where your default settings will be remembered? It can be quite tedious to reconfigure the comm settings everytime you want to use the sw.

Thanks.
We realy need to check why you can't work with E700.
About your suggestion - it is really a good advice.


still dont work with the x460 and x640!!!!!!!
i use 15in1 santel cables and it shold work shouldnt it?
have any one unlocked these modells?

uffe
For me is working with normal santel or any serial E700 cable or use twister A300 cable.
Jankovic
03-09-2006, 10:05
Hello

Thanx For Update but problem is still there ... I use UFS3 and USB smart but same error ........

Mario
dani146
03-09-2006, 11:38
Hello

Thanx For Update but problem is still there ... I use UFS3 and USB smart but same error ........

Mario

ahhhhhhhhhhhhhhh
Man - just check your screenshot !!!
You did not select any speed to BAUD RATE (speed on comm port)
uffehbg
03-09-2006, 12:40
this is what i get everytime!!

Presss On Or Insert Autoignition Cable
Wait...
Timeout.Repeat Operation!

after i connect phone and it is switched off! i get the message that i shold switch on the phone wituch i do!
then i get the wait.....
timeout.repeat operation!
i select the right com port wich is 6 i checked and i tried al different speeds!
what can i do
i looked in my computer and got this from my com ports:

usb data cable vcp (com6)
is that correct for the santel cables? or do i have the wrong drivers?

plz answer zuela or dani!
need help now!
uffehbg
03-09-2006, 12:55
i have santel cables but with usb connection! does that matter?
i dont have the serial/com port one!
but i connect i get a virtual com port which is 6! and i choose that one when i connect!

uffe
uffehbg
03-09-2006, 13:47
i forgot to say that i have the santel 15in1 tool but with usb connection not the one that you connect to your com port
Arion123
03-09-2006, 21:57
HI Dani146!

I have bought the Samsung Santel COM Cable set from you;)

I need the Santel PS2 cable Pinout ( Male), because I want to fit for this cable set to the USB interface ( FTDI chip, Profolic 2303, CP2102 Chip etc.)

I succeed in identify the 4 Pin out:)

1. Orange: VccPh
2. Green : GND
3. Red : Phone Tx
4. Balck : Phone Rx

But I don't find that where should I connect the Yellow and Brown wires.
Can You Help ME , that i could find this information??



Br: Arion
alfred62
03-10-2006, 10:40
use E700 cable phone off push info push starbuttom on phone insert another card insert nck code unlocked tested all ok
Tegards
still dont work with the x460 and x640!!!!!!!
i use 15in1 santel cables and it shold work shouldnt it?
have any one unlocked these modells?

uffe
Inovator
04-13-2006, 22:32
HI Dani146!

I have bought the Samsung Santel COM Cable set from you;)

I need the Santel PS2 cable Pinout ( Male), because I want to fit for this cable set to the USB interface ( FTDI chip, Profolic 2303, CP2102 Chip etc.)

I succeed in identify the 4 Pin out:)

1. Orange: VccPh
2. Green : GND
3. Red : Phone Tx
4. Balck : Phone Rx

But I don't find that where should I connect the Yellow and Brown wires.
Can You Help ME , that i could find this information??



Br: Arion

yes, I have the same question...
does anyone know?
Arion123
04-14-2006, 11:20
HI All!

I succeed in identify the all Pin out

1. Orange: VccPh
2. Green : GND
3. Red : Phone Tx
4. Balck : Phone Rx
5. Yellow: Data in
6. Brown: Data Out But you have to make short the Brown and Yellow wires

My cabel is working perfect with SANTEL cables :)

Br: Arion
banalven1
04-30-2006, 05:58
i have the problem too.
use ufs interface connect to phone and press info always say WAIT :confused:
i tried all different speeds.
plz anyone can tell me step by step to connect samsung phone~
DarkSkir
04-30-2006, 09:37
i have the problem too.
use ufs interface connect to phone and press info always say WAIT :confused:
i tried all different speeds.
plz anyone can tell me step by step to connect samsung phone~

press info and then connect cabl to phone :D
BesTCooL
05-01-2006, 18:46
solution here click :
http://forum.gsmhosting.com/vbb/showthread.php?t=290069
Death Rider
05-02-2006, 09:25
HI All!

I succeed in identify the all Pin out

1. Orange: VccPh
2. Green : GND
3. Red : Phone Tx
4. Balck : Phone Rx
5. Yellow: Data in
6. Brown: Data Out But you have to make short the Brown and Yellow wires

My cabel is working perfect with SANTEL cables :)

Br: Arion
Bay cruiser it's have the same pinout that santel
KelvinShadow
05-02-2006, 09:35
Use E860 cable, to unlock X660 by SMART. But select X480 as model, it will unlock it 100% tested for very many times!!! :cool:

Good luck with it!

Kelvin